Determine the temperature rise

Assignment Help Civil Engineering
Reference no: EM13557074

1.Helium(15 degrees Celsius, 1atm) will be transported in a straight horizontal copper tube over a distance of 150 m at a rate of 0.1 m^3/s. If the pressure drop in the tube should exceed 6 in h20, what is the minimum pipe diameter? ( first classify the problem as case 1, 2 , or 3)

2.The electrical power supplied to the motor is 90 kW. The motor in turn delivers 100 hp at a speed of 1000 rpm to a hoist arrangement for an elevator. Define the electric motor as the system and calculate the rate of work for the system.

3.A low consumption solar refrigerator uses 12-v d.c. battery for the supply of 60 W of electrical power to the motor that drives the compressor of the refrigeration device. What is the current supplied to the motor?

4.A 45 W electric mixer is operated for 5 minutes while mixing a 2 kg shake. Assume Csubv=4200 J/kg-K for the liquid. Determine the temperature rise (in degrees C) of the milk shake.

Reference no: EM13557074

Questions Cloud

What temperature will the chip be operating at when the fan : An electronic chip internally generates 1.5 Watts of heat energy that must be dissipated to ensure its reliable operation. A fan, with an exposed area of 10cm^2 is attached to the chip so the heat can be transferred away by convection.
Calculate the final temperature of the gas : A well-insulated rigid vessel of volume 0.2 m^3 is divided into two equal compartments by thin diaphragm, as illustrated in the accompanying figure. One of the compartments is a vacuum
Determine the corresponding increase in water temperature : Water flows over a waterfall that is 60m high. Assuming that all of the potential energy of the water at the top of the fall is converted to an increase in internal energy at the bottom of the fall
Calculate the change in length of a 30m measuring tape made : Calculate the change in length of a 30m measuring tape made of steel when its temperature changes by 84 F. The coefficient of thermal expansion for steel is x = 3.1 x 10^-6 per C
Determine the temperature rise : A 45 W electric mixer is operated for 5 minutes while mixing a 2 kg shake. Assume Csubv=4200 J/kg-K for the liquid. Determine the temperature rise (in degrees C) of the milk shake.
Neglecting drive train losses what is the average power : A cyclist rides up a local mountain at an average speed of 11 mph. The road has an average grade of 5.5%. The cyclist and her bike have a combined mass of 75 kg. The force from road drag is 2.5 N and the aerodynamic drag (in Newtons)
Sub 12 means from stage one to two heat transfer : Sub 12 means from stage one to two. Heat transfer (Qsub12) occurs to a fluid of mass m whose volume increases at a constant pressure of 21 bar. Assume that the fluid is air (Csubv=0.718 kJ/kg *K and R=0.287 kJ/kg*K) and that Tsub1=725K and Tsub2=1100..
What is the change in internal energy of the system : What is the change in internal energy of the system? Assume the displacement work in a (fully resisted) constant pressure process is given by (*sub 12 means from stage 1 to 2) Wsub12=p(Vsub2-Vsub1).
What should the spring stiffness be if the spring : A 2 kg block is projected up a frictionless plane with and initial speed of 8 m/s. The plane is inclined upward at 30°. If the block travels 5 m before striking a linear spring, what should the spring stiffness be if the spring compression is to be l..

Reviews

Write a Review

Civil Engineering Questions & Answers

  At what height in the resevoirmust the water level be kept

Water at 20 Degree C is pumped at a constant rate of 9m^3/h from a large resevoir resting on the floor to the open top of a anexperimental absorption tower.

  Determine maximum moment in the beam if spinned at both ends

If the live load on a 30 foot long beam is 1.2 kip/feet and the dead load is 0.8 kip/feet determine the maximum moment in the beam (kip-ft) if it is pinned at both ends. Assume the weight of the steel is 0.3 kip/feet.

  Better for the environment based on the data

Discuss whether shoe A (leather) or shoe B (synthetic) is better for the environment based on the data in the table below. Is it possible to weight one aspect (air

  Determine aerodynamic drag on the full-scale prototyple car

The aerodynamic drag of a new sports car is to be predicted at a speed of 50mph at an air temperature of 25 degrees Celcius. Automotive engineers build a one-fifth scale model of the car to test in a wind tunnel.

  Determine largest value of ft for which solution is stable

A stream conveying a flood peak of 50 m3/s (velocity 1.25 m/s and depth 1 m) is divided into 1 km long reaches for solution of the unsteady equations. Determine the largest value of ft for which the solution will be stable.

  Calculate the hardness of lime water as mg per l as caco3

38 mL of 0.02 N HCl is added to neutralize 50.0 mL of lime water (Ca(OH)2). Calculate the hardness of lime water as mg/L as CaCO3 and mg/L as Ca(OH)2.

  How fast will ball c be traveling after all collisions cease

Three particles are sliding along a flat, frictionless surface. mA = 0.4 kg, mB = 0.5 kg, and mC = 0.4 kg. Before any collisions take place, vA = 15i m/s, vB = 10im/s, and vC = 5 m/s. e = 0.85 between A and B and e = 0.6 between B and C.

  What is the bod concentration at the outflow of the pond

A pond is used to treat a dilute municipal waste-water before the liquid is discharged into a river. The inflow to the pond has a flow rate of Q = 4,000 m3/day and a BOD concentration of Cin = 25 mg/L.

  Determine the minimum length of curve that can be designed

you are designing a highway to AASHTO guidelines on rolling terrain where the design speed will be 65 mi/hr. At one section, a +1.25% grade and a -2.25% grade must be connected with and equal tangent vertical curve.

  Calculate the final length and final diameter of specuman

A cylinder with a 6.0 in., diameter 12.0 in. height is put under a compresive load of 150 kips. The modulus of elasticity for this specimen is 8000 ksi and Poisson's ratio is 0.35. calculate the final length and the final diameter of this specuman..

  Determine the additional tension in each wire

The rigid bar AD is supported by two steel wires of (1/16)" diameter (E=29x10^6 psi) and a pin and bracket at D. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 120-lb load P is applied at B

  What is the maximum distance between the two particles

Before the second particle catches the first particle, what is the maximum distance between the two particles.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd