Determine the temperature of the exiting moist air stream

Assignment Help Mechanical Engineering
Reference no: EM131016936

Moist air at 95°F, 1 atm, and a relative humidity of 30% enters a steam-spray humidification device operating at steady state with a volumetric flow rate of 5700 ft3/min. Saturated water vapor at 230°F is sprayed into the moist air, which then exits the device at a relative humidity of 50%. Heat transfer between the device and its surroundings can be ignored, as can kinetic and potential energy effects. Determine

(a) the temperature of the exiting moist air stream, in °F.

(b) the rate at which steam is injected, in lb/min.

Reference no: EM131016936

Questions Cloud

Franzi and tony expected npv : There's a 50-50 chance of strong or weak lunch economy. Franzi's and Tony's Cost of Capital is 10%. What is Franzi's and Tony's expected NPV?
Determine the mass flow rate of dry air required : The heated air is then allowed to pass over the materials being dried, exiting the dryer at 150°F, 1 atm, and 30% relative humidity. If moisture is to be removed from the materials at a rate of 2700 lb/h, determine the mass flow rate of dry air re..
Why is this relevant and what is the role of leadership : Why is this relevant and what is the role of leadership?
Is every function a relation : What is the difference between an equation that is a function and one that is not - Is every function a relation? Is every relation a function?
Determine the temperature of the exiting moist air stream : Saturated water vapor at 230°F is sprayed into the moist air, which then exits the device at a relative humidity of 50%. Heat transfer between the device and its surroundings can be ignored, as can kinetic and potential energy effects. Determine t..
Construct a dot plot to represent the data : Construct a dot plot to represent the data. Use the number line provided - The table shows the number of hours worked per server.
Determine temperature of moist air leaving spray section : Moist air at 32°C and = 77% enters the system and passes through a water spray, leaving the spray section cooled and saturated with water. The moist air is then heated to 25°C and = 45% with no change in the amount of water vapor present. For ..
Net result after the stock : A trader sold a Sep 50 straddle for $8. At expiration, the stock closed at $49. What was the net result after the stock was delivered to the trader who then sold the stock for $47.50?
Determine temperature and relative humidity at duct inlet : A fan within an insulated duct delivers moist air at the duct exit at 22°C, 60% relative humidity, and a volumetric flow rate of 0.5 m3/s. At steady state, the power input to the fan is 1.3 kW. Using the psychrometric chart, determine the tempera..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd