Determine the temperature of the air at the compressor exit

Assignment Help Mechanical Engineering
Reference no: EM13610044

An air compressor operates at steady state with air entering at p1=1 bar, T1 =17 C and exiting at P2=5 bar. The air undergoes a polytropic process for which the compressor work input is 162.2 kJ per kg of air flowing. Determine: a. The temperature of the air at the compressor exit b. The heat transfer in kJ/kg of air flowing c. Sketch the process on a p-v and T-s diagrams and indicate the work and heat transfers. i. Assume ideal gas and neglect kinetic and potential energies.

Reference no: EM13610044

Questions Cloud

A specific automotive part that a service station stocks in : a specific automotive part that a service station stocks in its inventory has an 8 chance of being defective. suppose
Richard exchanges a building with a fmv of 80000 a basis : richard exchanges a building with a fmv of 80000 a basis of 35000 and subject to a liability of 30000 for land with a
It is approximately 5800 kelvin on the surface of the sun a : it is approximately 5800 kelvin on the surface of the sun.a. how much faster do sound waves travel there than on earth?
Accumulated depreciation-equipment at 1110 was 230000 at : accumulated depreciation-equipment at 1110 was 230000. at 123110 the balance of the account was 380000. during 2010 one
Determine the temperature of the air at the compressor exit : an air compressor operates at steady state with air entering at p11 bar t1 17 c and exiting at p25 bar. the air
Gold clothing store had a balance in the accounts : gold clothing store had a balance in the accounts receivable account of 820000 at the beginning of the year and a
Two speakers are playing two different but pure : two speakers are playing two different but pure frequencies fa 110 hz an a two below middle c and fb 124 hz the b one
Fnd the area under the standard normal curve between z : a find the area under the standard normal curve between z -1.9 and z 1.17 p-1.9 lt z lt 1.17. give your answer
The nazareth companys mixing department incurred : the nazareth companys mixing department incurred conversions costs of 650820 during january after recording a beginning

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The mechanical errors in the joint and the inputoutput

the revolving joint type v of an industrial robot has a range of 240? rotation. the mechanical errors in the joint and

  Determine the exit temperature

Determine (a) the exit temperature, (b) the exit relative humidity of the air, (c) the exit velocity.

  A power plant operates a regenerative rankine cycle

A power plant operates a regenerative Rankine cycle with a reheat, one closed and one open feedwater heater and has a net power output of 1.2 x 109 Btu/hr. When the steam exits the boiler it's temperature is 1000°F and its pressure is 1400psi...

  Unidirectional reinforced composites1 calculating the

unidirectional reinforced composites1. calculating the mechanical properties of unidirectionally reinforced composites

  The 24m wide portion abcd of an inclined cantilevered

the 2.4m wide portion abcd of an inclined cantilevered walk-way is partially supported by members ef and gh. knowing

  Landing gear system structural design

Problem Statement Consider the landing gear shown below. Working in teprns of two, come up with a single optimized design for given operational conditions and design considerations

  Determine the latent heat of vaporization of the water vapor

How would you calculate the sensible heat, the latent heat, and determine the latent heat of vaporization of the water vapor in this air stream as the air is cooled from 170 F to 48 F?

  What is the initial velocity of block b

What is the initial velocity of Block B, constant acceleration of Block A, velocities of both blocks at t=3s, and the total distance traveled by block B from t=0s to t=3s?

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Determine the force p

the coefficients of static friction and kinetic friction 0.4, 0.30 between all surface of contact. determine the force p for which motion of the 30kg block is impending if cable AB is attached is shown and removed.

  Suppose that you are the ownermanager of a small business

an important part of a project is to identify the key process input variables kpiv and key process output variables

  In an experiment similar to the procedure set out for part

in an experiment similar to the procedure set out for part a of the calorimetry experiment 1.500 g of mgs was combined

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd