Determine the surface temperature of the top of the puck

Assignment Help Mechanical Engineering
Reference no: EM13612801

Consider an NHL regulation hockey puck 3 inches in diameter and 1 inch thick (7.62 cm by 2.54 cm). Determine the surface temperature of the top of the puck after an 83 MPH (37 m/s) slapshot from center ice by Paval Datsyuk. The ice temperature is -4°C and the temperature of the air in the Joe Louis Arena at ice level is kept at 17°C. The heat transfer may be assumed to be steady state and one-dimensional through the puck between the ice and the air (k= 0.2 W/mK for the Vulcanized rubber puck). A thin water film develops during the slapshot that is 3.5 mm thick between the puck and the ice. This water film is considered a bounded flow between the puck and the ice.

Reference no: EM13612801

Questions Cloud

Consider the following joint discrete probability mass : consider the following joint discrete probability mass function pmfpxy 0.1 for xy 11 21 12 and 220.2
Use your calcuator to perform a linear regression on this : fred wants to figure out how much extra it cost him to heat his house at 75.00 f so he does an experiment. he picks a
Recently the management team at wilson noticed that there : recently the management team at wilson noticed that there were differences in output levels across the various plants.
Hark inc had cash sales of 400000 and credit sales of : hark inc. had cash sales of 400000 and credit sales of 1100000. the accounts receivable balance increased 25000 during
Determine the surface temperature of the top of the puck : consider an nhl regulation hockey puck 3 inches in diameter and 1 inch thick 7.62 cm by 2.54 cm. determine the surface
Assume that the positively charged particle starts at point : assume that the positively charged particle starts at point a with an initial velocity in the positive x-direction.
A 300g ball is tied to a string it is pulled to an angle of : a 300g ball is tied to a string. it is pulled to an angle of 4.00 degrees and released to swing as a pendulum. a
X is 50 years old unmarried without children and has : x is 50 years old unmarried without children and has earnings during 2011 of 8000. he is not claimed as a dependent on
A person with a mass of 50 kg is standing on a scale in an : a person with a mass of 50 kg is standing on a scale in an elevator that is accelerating upwards at a rate of 3.2 ms2.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd