Determine the stresses at the point of tube 1

Assignment Help Civil Engineering
Reference no: EM131152348

A tray rests on an extendible arm consisting essentially of two steel tubes of different outer diameters. The downward force is applied at the tray center F0 = 1000 N. Determine the stresses at the point of tube 1 where the bending and torsional stresses are greatest. Draw the Mohr's circle for that stress state. Both members have a wall thickness of 4 mm

458_641931d3-d719-44e0-8645-1eb3241407e1.png

Reference no: EM131152348

Questions Cloud

Costs for a month : Bubba's Steakhouse has budgeted the following costs for a month in which 1,600 steak dinners will be produced and sold: Materials, $4,080; hourly labor (variable), $5,200; rent (fixed); depreciation, $720; and other fixed costs, $570. Each steak d..
Determine the total charge entering a terminal : Determine the total charge entering a terminal between t=1 and t=2s if the current passing the terminal is i= (3t2-t)A.
Semitool actual excess return : Semitool's products experience more rapid growth than anticipated, thus pushing up the stock price by another 1%. Based on this information, what was Semitool's actual excess return?
What is swimkid margin of safety : Swimkids is a swimsuit manufacturer. They sell swim suits at a selling price is $30 per unit. Swimkids variable costs are $18 per unit. Fixed costs are $70,900. Swimkids expects sales of $268,000 next year. What is Swimkid's margin of safety (in d..
Determine the stresses at the point of tube 1 : Determine the stresses at the point of tube 1 where the bending and torsional stresses are greatest. Draw the Mohr's circle for that stress state. Both members have a wall thickness of 4 mm
Estimated total costs for a production : Total costs were $73,000 when 28,000 units were produced and $96,000 when 36,000 units were produced. Use the high-low method to find the estimated total costs for a production level of 32,000 units.
Describe a high-level timeline that includes key tasks : Describe at least three (3) key milestones and /or deliverables for your project. Describe a high-level timeline that includes key tasks and deadlines. Estimate the project's overall cost and any key staffing and non-staffing resources needed
Expected for the company stock price : The stock price of W Co. is $65. Investors require an 11 percent rate of return on similar stocks. If the company plans to pay a dividend of $3.75 next year, what growth rate is expected for the company's stock price?
Company target debt-equity ratio : Fama's Llamas has a weighted average cost of capital of 10.4 percent. The company's cost of equity is 13 percent, and its pretax cost of debt is 8.4 percent. The tax rate is 40 percent. What is the company's target debt-equity ratio?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the tensile force on the weld per foot

Due to a leak in Pump Station 1,the Alaska pipeline is shut down briefly.The pipe line is half full.Assume the pipe is welded horizontally at its midpoint.What is the tensile force on the weld per foot? Assume Ø=40”and ?oil=53.55lb/ft3.

  Determine the mass flow rate of the required makeup water

A natural-draft cooling tower is to remove 50 MW of waste heat from the cooling water that enters the tower at 42°C and leaves at 27°C.

  Write expression for engineering strain associated with a

A piece of wire is stretched from length l1 to length l2 (step A), and then from length l2 to length l3 (step B). (i) Write down an expression for the engineering strain associated with step A.

  Maximum deflection of the beam

Determine the deflection of the right end of the pointer and the maximum deflection of the beam.

  How to estimate for the loaded machines on level ground

Stripping overburden in the Illinois coal belt, the Dusty Coal Company uses 270-horsepower, track-type tractors (with direct-drive transmissions) and drawn scrapers.

  Determine the rate of heat transfer to the stock in furnace

Cylindrical, steel bar stock (density = 7833 kg/m3, Cp = 0.465 kJ/(kg C)) of 10-cm diameter is heat-treated by drawing it at a velocity of 3 m/min through a 6-m-long furnace maintained at 900C.

  What is the max tensile force that could be applied to steel

a rectangular piece of steel is 10" wide by 60" long by 3" deep, what is the max tensile force that could be applied to the steel, and what is the total elongation of the steel

  Determine what is the current value of grannys savings

Granny viola has been saving money in the Bread and Butter mutual fund for 15 years . She has been a steady depositor over those years and has a pattern of putting $100 into the account every 3 months.

  Determine the minimum length of curve that can be designed

You are designing a highway to AASHTO guidelines on a rolling terrain where the design speed will be 60 mi/h. at one section, a +1.0% grade and a -3.0% grade must be connected with an equal-tangent vertical curve.

  Write an expression that executes the exclu() memberfunction

write an expression that executes the exclu() member function in this object.

  Problem regarding helium balloons

To float a 160 pound man using helium balloons (assume 0.52 cubic feet per inflated balloon). How many balloons would it take? Assume density of air is 1.29 kg/cubic meter and the density of helium is 0.179 kg/cubic meter.

  Determine the probability of failure of the structure

If the load effect has a mean value of 88 kips and a standard deviation of 1.8 kips. If the nominal material strength is 160 kips Determine the followings 1- The probability of failure of the structure under the nominal resistance and service load..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd