Determine the state of the ammonia after the throttling

Assignment Help Mechanical Engineering
Reference no: EM13638455

Water and ammonia streams flow through a steady state heat exchanger. The water stream enters the heat exchanger with a velocity of 40 m/s, a temperature of 200°C, and a pressure of 15 bar through a pipe with a diameter of 0.1 m. The water stream leaves as a saturated liquid-vapor mixture with a quality of 0.2. Before entering the heat exchanger, the ammonia stream flows through a throttling valve. At the inlet of the throttling valve the ammonia pressure and temperature are 12 bar and 28°C. At the exit the pressure of the ammonia stream has dropped to 4 bar. The stream then enters the heat exchanger and exits with a temperature of 60°C. The pressure drop across the heat exchanger is negligible for both the ammonia and water streams. Neglect heat transfer to the surroundings.

(a) Determine the mass flow rate (kg/s) of the water stream.

(b) Determine the mass flow rate (kg/s) of the ammonia stream.

(c) Determine the state of the ammonia after the throttling process. If the ammonia is a saturated liquid-vapor mixture, calculate the quality x2.

Reference no: EM13638455

Questions Cloud

Three long parallel wires each carry a 2 a current with two : three long parallel wires each carry a 2 a current with two of the currents up and one down. the wires pass through the
An electrolytic cell is constructed that produces solid : an electrolytic cell is constructed that produces solid pbfrom . if 2.82 a flows for 19 minutes through the cell. how
Two long vertical wires are separated by 2m the one on the : two long vertical wires are separated by 2m. the one on the left carries a current of 8 a upward and the other carries
A projectile is launched at speed vo from the foot of an : a projectile is launched at speed vo from the foot of an incline that makes angle theta22.0 degrees relative to the
Determine the state of the ammonia after the throttling : water and ammonia streams flow through a steady state heat exchanger. the water stream enters the heat exchanger with a
What is the magnetic potential energy of a 2 cm diameter : what is the magnetic potential energy of a 2 cm diameter circular loop carrying a 1a current when placed in a 2 t
A mass spectrometer can detect the different isotopes of an : a mass spectrometer can detect the different isotopes of an ionized element. if zn 2 ions are accelerated through a 10
Verify your finite difference code solution against a : develop a one-dimensional transient numerical solution for a plane wall of a nuclear containment vessel. the external
100 g of ice at 0deg is added to 3000 g of waterat 60degc : 100. g of ice at 0deg is added to 300.0 g of waterat 60degc. assuming no transfer of heat to the surroundings what is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd