Determine the speed and direction of the wind

Assignment Help Mechanical Engineering
Reference no: EM13948509

1. A car is traveling north along a straight road  at 50 km>h. An instrument in the car indicates that the wind is coming from the east. If the car's speed is 80 km>h, the instrument indicates that the wind is coming from the northeast. Determine the speed and direction of the wind.

2. Two boats leave the shore at the same time and travel  in  the  directions   shown.   If   vA  = 10 m>s and v= 15 m>s, determine the velocity of boat with respect to boat B. How long after leaving the shore will the boats be 600 m aprt?

Reference no: EM13948509

Questions Cloud

Prepare all journal entries : Prepare all journal entries, consistent with GAAP, including budgetary and encumbrance entries that the department should make in 2015.
Describe the problem and present the data : The financial team has assembled to review labor data for a new engine. Designed for efficiency, the new engine's power to weight ratio and low drag geometry promised great things. Dashiell kicked off the meeting. "Folks, this is radical. For the ..
Convenient way to document a system events : A use case is a convenient way to document a system's events. It serves as a kind of table of contents for the business events and activities that must be supported by the system. It will be used to identify how the system will be used and which a..
Did the business show a negative cash balance for june : Did the business show a negative cash balance for June? Assuming that the owner has no hope of establishing a line of credit for the business, what recommendations would you give the owner for dealing with a negative cash balance?
Determine the speed and direction of the wind : A car is traveling north along a straight road  at 50 km>h. An instrument in the car indicates that the wind is coming from the east. If the car's speed is 80 km>h, the instrument indicates that the wind is coming from the northeast. Determine the..
Difference between the 2 graphics : It is the business that has the knowledge about their entities (things of importance) and what kind of unique information that separate them (invoice numbers, customer IDs, and so on).
Determine velocity and acceleration of end of cord : The cord is attached to the pin at C and passes over the two pulleys at A and D. The pulley at A is attached to the smooth collar that travels along the vertical rod. Determine the velocity and acceleration of the end of the cord at B if at the ins..
What is the population mean you are trying to estimate : Suppose you are trying to estimate the average miles per gallon for a new brand of car. You take a random sample of 40 cars, and, for this sample, the average miles per gallon is 32 and the standard deviation for this sample is 2.2. Answer the fol..
Coefficient of restitution between block and rod : A 2-lb block, sliding on a smooth horizontal surface with a velocity of 12 ft> s, strikes the rod at its end B. Determine the velocity of the block immediately after the collision. The coefficient of restitution between the block and the rod at B i..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the stress-strain and total elongation

A 24 in long bar with a cross sectional area of 1.0 in^2 is subjected to an axial tensile load of 10,000 lb. compute the stress, strain and the total elongation if the bar material is :

  Properties enthalpy and entropy are deriven from heat

In thermodynamics, path functions such as heat or work are dependent on path process, point functions are not. Properties enthalpy and entropy are deriven from heat and work relationships. However, when we calculate these properties just like point f..

  Draw the bar graph of probability vs outcome i can do

let x denote the sum of the face values of a die rolled twice i.e. the outcome of this experiment is the sum. assume

  Superheated steam pressure at a 1 atm mean temperature of

superheated steam pressure at a 1 atm mean temperature of 800kand mass flow rate of 0.15kgs enters a thin walled

  Water is the working fluid in regenerative rankine cycle

Water is the working fluid in a regenerative Rankine cycle. The pressure and temperature at the turbine inlet are 8MPa and 550?C, respectively, and the condenser pressure is 7.5KPa. The mass flow rate of steam entering the turbine is 176kg/s.

  The relative acceleration of block d with respect respect

the system shown starts from rest and each component moves with a constant acceleration. if the relative acceleration

  Assume that the water is incompressible with a density of

water flows steadily through an outflow nozzle. known conditions are d1 15 cm v1 3 ms d2 9 cm. assume that the water

  Derive an expression for the work done on the gas it is a

an ideal gas p? mrt is heated at constant volume until its temperature is doubled and then cooled at constant pressure

  Electrical conductivity of the pipe

The electrical conductivity of the pipe ke is constant over the temperature range of interest. The local rate of electrical heat production Se is then uniform throughout the pipe wall.

  Calculate rate of heat transfer

The heat transfer coefficient in the oven is 25W/m^2K. Calculate rate of heat transfer per m^2 area.

  The pressure difference between the large and small

a venturi meter is used to measure the water flow in a 3cm diameter pipe. the diameter of the narrow section is 1.5 cm.

  Calculation of average pressure and upsetting force

Calculation of average pressure and upsetting force in forging and how to minimize barrelling effect - barrelling caused by friction can be minimized by applying an effective lubricant or ultrasonic vibration

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd