Determine the specific volume of the rock

Assignment Help Mechanical Engineering
Reference no: EM13708186

A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg

Reference no: EM13708186

Questions Cloud

Convert the composition to atomic percent : A copper and nickel alloy has the following composition: 80wt% Cu and 20wt% Ni. Convert the composition to atomic percent.
Derive the material balance equation : Derive the material balance equation for a tank with rigid and incompressible fluids for the following conditions...The tank is initially full of oil at Pi some oil is bled off to reduce the pressure to P1 the oil removed from the tank is collected a..
Determine the power required for steady speeds : Extensive testing of an experimental 2820-lb automobile reveals the aerodynamic drag force FD and the total no aerodynamic rolling-resistance force FR to be as shown in the plot. Determine (a) the power required for steady speeds of 22 and 44 mi/hr o..
Calculate the density of the air in the round section : At one section in an air distribution system, air at 14.7 psi and 100degree F has a velocity of 1200 ft/min a and the duct is 12 in x12 in square. At another section the duct is round with a diameter of 18 inches and the velocity is 900 ft/min. Calcu..
Determine the specific volume of the rock : A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg
A turbine extracts energy from water flowing through : A turbine extracts energy from water flowing through a 11-cm-diameter pipe at a pressure of 700 kPa with an average velocity of 11 m/s. If the turbine is 90 percent efficient, how much energy can be produced if the water is emitted from the turbine t..
Determine the temperature of the air and the initial volume : 1750g of air performs an expansion work of 3100kJ on the surrounding as it expands isothermally to a pressure of 63000kPa ad a volume of 0.065 cubic meters. Determine the temperature of the air and the initial volume.
Undergoes a reversible adiabatic process : In a polytropic process, a fluid is compressed to 2.75 times its initial pressure, whereas its temperature becomes1.65 times. What is the fluids index of expansion, n? 1.2kg of Air at a pressure of 2.15MPa and a temperature of 585K, undergoes a rever..
Determine the mass of the air-initial temperature of the air : Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initia..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd