Determine the specific internal energy

Assignment Help Mechanical Engineering
Reference no: EM133434372

Question: A refrigerant flows into an expansion valve with the following properties: Vel = 35 m/s; e=184.56 kJ/kg. If the potential energy can be considered zero, determine the specific internal energy. (kJ/kg)

Reference no: EM133434372

Questions Cloud

Working on a positive drainage problem : Working on a positive drainage problem. I've got the Tc (time of concentration), but how do you calculate QP? (QP being Peak Flow in Landscape planning/ hydro
Why is it important in developing a selection system : What is validity? Why is it important in developing a selection system? Why is it important in HR? What are the different methods that we use to assess validity
What is the angle of attack of the model : airfoil is mounted in the tunnel at an angle of attack such that the section lift coefficient is 0.2. a. What is the angle of attack of the model
Which type of performance pay type it belongs to : which type of Performance Pay Type it belongs to. Explain how the Performance Pay Option you chose does not increase financial liability to the company
Determine the specific internal energy : Vel = 35 m/s; e=184.56 kJ/kg. If the potential energy can be considered zero, determine the specific internal energy. (kJ/kg)
Determine the rate of entropy generation in the system : Assuming the block to be at steady state, a) Determine Qdot. (kW) b) Determine the rate of entropy generation in the system's universe
What are three ways that global hr differs from domestic hr : What are three ways that global HR differs from domestic HR, specifically in relation to Total Rewards?
Research a real-world company that uses child labor : Research a real-world company that uses child labor and/or slavery using the list provided in the reading links. Describe how the company uses child labor
Standardized classification systems : Explain and provide an example for each of the seven ways that standardized classification systems directly impact health care.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What would be the final temperature of 1 m3 of atmosphere

the atmosphere on mars is comprised of mostly carbon dioxide at a pressure of 600 pa that is not a mistake it is in pa.

  The inlet of the bend is 50 cm above the exit neglecting

water flowing in a horizontal 30 cm diameter pipe at 5 ms and 300 kpa gage enters a 90o bend reducing section which

  What are the reaction forces of a pendulum at the pivot

what are the reaction forces of a pendulum at the pivot point at angles 0 45 and 90 from the horizontal. the pendulum

  What are the general areas of it certification

Certifications usually are classified based on the computer industry area to which they most closely relate: application software, operating systems, programmer/developer, hardware, networking, digital forensics, security, the Internet, and databa..

  Find the gravitational force exerted on the sphere

A symmetric sphere, of radius a and mass M, has its centre a distance b (b > a) from an infinite plane containing a uniform distribution of mass σ per unit area. Find the gravitational force exerted on the sphere.

  Calculate the heat transfer from the products

Calculate the heat transfer from the products per amount of substance of CO2 in the gases leaving the heat exchanger if dissociation can be neglected at the lower temperature.

  Determine the final temperature

A closed, rigid tank is filled with a gas modeled as an idea gas, initially at 27 degrees C and a gage pressure of 300 kPa. The gas is heated, and the gage pressure at the final state is 367 kPa. Determine the final temperature, in C. The local atmos..

  After your calculations explain two practical strategies

calculate the cost per piece of a milling operation that is used to machine a pocket of 2x3x0.5 lxwxd. the material

  If the zero level of the meriam blue manometer fluid is 02

a rectangular tank open to the atmosphere is filled with water to a depth of 2.5 m as shown. a u-tube manometer is

  Draw a cash-flow diagram

Major overhaul expenses of $5,000 each are anticipated for a large piece of earthmoving equipment. The expenses will occur at EOY four and will continue every three years thereafter up to and including year 13. The interest rate is 12% per year.

  Determine the punching force required

A mild steel plate of thickness 15 mm has a 50 mm diameter hole punched in it. If the ultimate shear stress of the steel is 275 MPa, determine (a) the punching force required, (b) the compressive stress in the punch.

  Determine the resultant force in n

A horizontal stream of water is directed at the windscreen of a truck , as shown in the drawing.The flow rate of the water is 8 litres/s and the diameter of the nozzle is 50 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd