Determine the spatial shear stress distribution in the pipe

Assignment Help Mechanical Engineering
Reference no: EM131461264

Q1. A horizontal straight pipe of an impermeable solid material extends in the z-direction for a length L and has a circular cross section, of radius r = a. An incompressible Newtonian fluid is undergoing steady state, low Reynolds number, laminar, unidirectional, rectilinear pressure driven flow in the z-direction of the pipe.

1362_Figure.png

(a) Write down the appropriate complete conservation of linear momentum equation.

(b) Simplify the equation of linear momentum for the given problem conditions. Indicate the basis on which you are eliminating terms.

(c) Determine the spatial shear stress distribution in the pipe.

(d) Determine the spatial velocity distribution in the pipe.

(e) Determine the average velocity in the pipe.

Q2. The erythrocyte sedimentation rate test of blood is often used as a diagnostic for immune disorders and other diseases. Assume a red blood cell (erythrocyte) is approximately a sphere of diameter Dp = 5 [µm]. Red blood cell density is ρp = 1125 [kg/m3] and the liquid plasma it is settling in has a density ρf = 1025 [kg/m3] and a viscosity µ = 1.5 [cP].

(a) Determine the sedimentation rate (velocity) for a single red blood cell.

(b) Verify the equation you used in part (a) is correct.

Q3. Chromatographic separation of proteins can be accomplished using resin ion exchange beads. Spherical Dowex 50-X8 beads of diameter Dp = 0.56 [mm] are packed in a cylindrical chromatography column of radius R = 0.1 [m] and length L = 1 [m] at a porosity ε = 0.35. The proteins are in solution in water of density ρ = 1000 [kg/m3] and viscosity µ = 1 x 10-3 [Pa s], that is fed to the column at a volumetric flow rate of Q = 2.133 x 10-4[m3/s]. Determine the pressure drop across the column. Verify any simplifications you make.

Q4. The following equation is a simplified θ-direction linear momentum balance for an incompressible fluid. Using the letters identify the physical type of each term.

1212_Figure1.png

i) The viscous force density

ii) The pressure force density

iii) The time dependent acceleration force density

iv) The inertial force density

v) The gravitational force density

Reference no: EM131461264

Questions Cloud

Comment on their efficacy in terms of consumer protection : Do a research on these two regulatory agencies and comment on their efficacy in terms of consumer protection.
European and valid as is rome latin offspring : Byzantium's Greek legacy is as European and valid as is Rome's Latin offspring, but where would we expect to find it in today's Europe?
What argument does king make about the southern church : "What justification does Jackson cite for the government policy toward removal of Indian tribes from their traditional lands?"
Considering investing in shares of starbucks : Suppose you are considering investing in shares of Starbucks. Explain how each of situations would make you more or less willing to actually invest in shares.
Determine the spatial shear stress distribution in the pipe : Write down the appropriate complete conservation of linear momentum equation. Determine the spatial shear stress distribution in the pipe
Relationship between us foreign policy and terror : Essays that rely on a narrow range of sources, are disorganized, do not cite sources or cite them improperly, or employ incorrect grammar or sentence structure.
Explain how you would design a network for the given firm : Write a professional letter to the CEO of the company explaining how you would design a network for firm. Learn to optimize a design based on cost constraints.
How did slavery in northern colonies differ : How did slavery in Northern colonies differ from the enslavement of Africans in the Southern colonies?
What is the total cost of the pharmaceuticals : Arizona Health Services (AHS), a large hospital system, What is the economic order quantity? What is the total cost of the pharmaceuticals?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The accompanying table provides additional data at the two

five kg of water contained in a piston cylinder assembly expand from an initial state where t1400 degree celsius p1700

  What power would be expected to operate the prototype pump

A large pump delivering 1.2 m3 /s of water with a pressure rise of 400 kPa is needed for a particular hydroelectric power plant. A proposed design change is tested on a smaller 1:4 scale pump. Estimate the flow rate and pressure rise which would b..

  Find a the heat transfer in the heat exchanger kw b the

an aircraft cooling system bleeds air from the engine compressor at 300 kpa and 200 c at the rate 0.09 kgs. the air is

  Strong authentication and authorization

You have been asked to design a secure system that requires strong authentication and authorization. The system must be designed so that communications between parts of the system cannot be intercepted and read by an attacker.

  What is the minimum required thickness tmin

If the allowable tensile stress in the bar is 12,000 psi and the height h= 1.25 in., what is the minimum required thickness tmin?

  The density of seawater can be taken to be 1025 kgm3 and

the ocean thermal energy conversion otec power plant takes advantage of the temperature difference between ocean

  Examine the rate of heat generation

Need help with determining the rate of heat generation required at the welding source to accomplish a weld. A fillet weld is used to join two medium carbon steel plates each having a thickness of 5.0mm.

  Determine the actual heat transfer rate

A shell and tube heat exchanger with one shell pass and four tube passes is being analyzed to determine the heat transfer rate and the fluid outlet temperatures for prescribed flow rates and inlet temperatures. The cold fluid has a heat capacity rate..

  Determine the allowable load p for the given values of r

Write a computer program to determine the allowable load P for the given values of r, D, the thickness t of the bar, and the allowable stress σall of the material. Knowing that t = 1/4 in., D = 3.0 in. and σall = 16 ksi, determine the allowable lo..

  Changes in kinetic and potential energy are negligible

A gas mixture at 675.0°C and 113 kPa absolute enters a heat exchanger at a rate of 69.0 m3/hr. The gas leaves the heat exchanger at 245.0°C. The change in enthalpy of the gas during the cooling process is -6.80 kJ/mol.

  Determine the mass moment of inertia of the object

The object shown is made of uniform plastic and weighs 2:34 lb. Determine the mass moment of inertia of the object about the axis indicated. Report your answer using slugs and feet.

  A what will be the resolved shear stress on the 11-1

a crystalline grain of iron in a steel plate is situated in such a way that a tensile stress of 100 mpa 14.5 ksi is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd