Determine the slip factor using busemann''s method

Assignment Help Mechanical Engineering
Reference no: EM131057276

A centrifugal pump is used to raise water against a static head of 18.0 m. The suction and delivery pipes, both 0.15 m diameter, have, respectively, friction head losses amounting to 2.25 and 7.5 times the dynamic head. The impeller, which rotates at 1450 rev/min, is 0.25 m diameter with eight vanes, radius ratio 0.45, inclined backward at β'2 = 60°. The axial width of the impeller is designed so as to give constant radial velocity at all radii and is 20 mm at impeller exit. Assuming a hydraulic efficiency of 0.82 and an overall efficiency of 0.72, determine

a. the volume flow rate;

b. the slip factor using Busemann's method;

c. the impeller vane inlet angle required for zero incidence angle;

d. the power required to drive the pump.

Reference no: EM131057276

Questions Cloud

Determine the impeller slip factor using wiesner''s formula : Also calculate values for slip factor using the equations of Stodola and Busemann, comparing the answers obtained with the result found from Wiesner's equation.
Calculate the absorbance of the unknown : An unknown solution containing a mixture of Red No. 3 and Green No. 3 has a %T of 34.1 at 524 nm and a %T of 50.7 at 628 nm. Calculate the Absorbance of the unknown at the two wavelengths.
Two countries and companies explored : Using the two countries and companies explored in Weeks Two and Six, write a paper of approximately 1,350 words in which you:
What is the chemical symbol for gold : 1. True or false? An electron carries a positive charge. 2. Famous New Zealand scientist Ernest Rutherford was awarded a Nobel Prize in which field?3. What is the chemical symbol for gold?
Determine the slip factor using busemann''s method : A centrifugal pump is used to raise water against a static head of 18.0 m. The suction and delivery pipes, both 0.15 m diameter, have, respectively, friction head losses amounting to 2.25 and 7.5 times the dynamic head.
First element on the periodic table : 1. What is the first element on the periodic table? 2. What is the centre of an atom called? 3. True or false? Acids have a pH level below 7.
Create a change model conducive to your field : Research the various change models used by organizations today. After assessing these models, create a change model conducive to your field, and that will work within your organization's culture.
Molarity of the acetic acid solution : If 35.7 mL of 0.220 MKOH is required to completely neutralize 26.0 mL of a HC2H3O2 solution, what is the molarity of the acetic acid solution?
What was the initial concentration : A 890 mL NaCl solution is diluted to a volume of 1.05 L and a concentration of 3.00 M. What was the initial concentration?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd