Determine the slederness ratio of a 5m column

Assignment Help Civil Engineering
Reference no: EM13312262

determine the slederness ratio of a 5m column with built in ends if its cross section is circular with a radious of 40mm abd b 50mm square use the concept of effective length ?

Reference no: EM13312262

Questions Cloud

How many cancers are caused by viruses : Tumor Viruses and our Current Understanding of Cancer and How many cancers are caused by viruses?
Explain what is the partial pressure of component : A mixture of gases contains 5.18 g of CO, 3.65 g of NH3, and 5.01 g of O2. If the total pressure of the mixture is 2.65 atm, what is the partial pressure of each component
What are the average velocities for the three intervals : A football quaterback runs 15.0 m staright down the playing field in 2.50s. what are the average velocities for the three intervals
Explain what would be the concentrations of acetic acid : What would be the concentrations of acetic acid and sodium acetate in this solution. Would we expect this solution to be a buffer
Determine the slederness ratio of a 5m column : determine the slederness ratio of a 5m column with built in ends if its cross section is circular with a radious of 40mm abd b 50mm square use the concept of effective length
Find the diamensions b and a with balanced stress : A reinforced concrete beam d = 18 in , and n = 10. find the diamensions b and a , that will resist a bending movement of 60 kip,ft with balanced stress reinforcement if fc =1600 psi and fs = 20 ksi
Determine the maximum axial compressive force to the bar : A short 60mm diameter circle bar is made of material for which the maximum safe compressive strees is 80 MPa and the maximum safe shearing strees is 30 MPa.
Discuss the distinction between spontaneous and designed : Discuss the distinction between spontaneous and designed order.Needs to be 1000 word essay relating to institutional economics. Drawing on readings from Coase, Williamson, Easterly and Henry and Miller.
Describe the construction and beneficial features of switch : An inductive proximity switch is a device used in valve feedback, describe the construction, operating principle and beneficial features of the switch

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum external pull the ferrari has

A ferrari with 808 hp has a max. speed of 211 mph at 6,300 rpm. the Ferrari weighs 4,155 lb/ton and is operated over a smooth concrete road with a rolling resistance of 40 lb/ton and a slope of 3%.

  Will stress cause composite to fail before tensile strength

a ceramic matrix composite contains internal flaws as large as 0.001 cm in length. The plane strain fracture toughness of the composite is 45 MPa sqr(m), and the tensile strength is 550 MPa.

  Determine the minimum required vehicle frequency

A light rail route has 2 terminals and 4 intermediate stations. The demand (passengers/hr) for morning peak hour is: North Terminal Station 1 Station 2 Station 3 Station 4 South Terminal

  Determine what fair amount contractor should receive

Determine what fair amount she should receive if she decides she want to be paid: a. In 2 equal installments - one immediately (at T=0) and one at the end of month 36.

  Elevation of the road at station

Given the following data for a vertical curve of a road; G1=-2.5%, G2=+5.5% and station of PVI=250+50.At station 252+50, the vertical curve must intersect an existing road at elevation 48.48ft. the elevation on the tangent section at station 256+5..

  Calculate by what factor the mass of propane has increased

A typical propane tank that we use for barbeque initially contains a pressure of 10 psi. The pressure is low, so we take it to the local store to fill the tank with more propane. After filling,the pressure is 100 psi.

  How long will it take for primary consolidation settlement

A compressible 12-ft clay layer beneath a building is overlain by a stratum of sand and gravel and underlain by impermeable bedrock. The total expected primary consolidation settlement of the compressible clay layer due to the building load is 4.6..

  Find the moment equations and then the deflection

a simple beam with a pin support at A on the left side of my beam, and a roller connection 20 feet away on the far right side of the beam labeled C, with the midspan point (10 feet) labeled B.

  Determining optimal solution

The company would like to distribute the songs between the two CDs such that the used space on each CD is about the same. Formulate the problem as an IP, and find the optimal solution.

  Determine the initial speed v0 and angle-theta required

The receiver's velocity is constant at 10 yd/sec, and he catches passes when the ball is 6 ft. above the ground. If the quarterback desires the receiver to catch the ball 2.5 sec. after the launch instant, determine the initial speed v0 and angle,..

  Determine the principal stresses and the principal angle

using the stress transformation quations only,given a stress state where sigma x=6500 psi,sigma y= 17,300 psi and tau xy=2900 psi, determine the principal stresses,the principal angle and the maximum shear stress.

  Write a computer program to calculate deflection at midpoint

Two 52 kN loads are maintained 2.5 m apart as they are moved slowly across beam AB. Write a computer program to calculate the deflection at the midpoint C of the beam for values of x from 0 to 9 m, using .5 m increments.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd