Determine the shearing stress at point p of thin-walled pipe

Assignment Help Electrical Engineering
Reference no: EM131154864

(a) Determine the shearing stress at point P of a thin-walled pipe of the cross section shown caused by a vertical shear V.

(b) Show that the maximum shearing stress occurs for θ = 90° and is equal to 2V/A, where A is the cross-sectional area of the pipe.

1277_bb18584b-b3b6-4df8-80d2-d1b38b3814ca.png

Reference no: EM131154864

Questions Cloud

Draw use case diagram of a person visiting post office : Draw use case diagram of a person visiting post office. What action a person can perform in post office. First draw on paper and then using ArgoUML.
Discuss what he means by physician autonomy : Discuss what he means by "Physician autonomy and the organized medical staff will become less relevant." Do you believe this will improve patient care
Describe the variable overhead variances : Describe the variable overhead variances. How does a manager plan for these variances? Compare the variable overhead variance to the fixed overhead variance.
Find any two candidate keys of r : Given R(A, B, C, D, E) with the set of FDs, F{AB → CD, ABC → E, C → A}, Find any two candidate keys of R
Determine the shearing stress at point p of thin-walled pipe : Determine the shearing stress at point P of a thin-walled pipe of the cross section shown caused by a vertical shear V.
Conditions that stochastic process is wide sense stationary : State at least two conditions necessary to guarantee that a stochastic process is wide sense stationary.
Prepare a ledger using t-accounts : Prepare a ledger using T-accounts. Enter the trial balance amounts and post the adjusting entries. Prepare an adjusted trial balance on May 31. Prepare an adjusted trial balance on May 31.
Mechanisms responsible for attenuation of ultrasonic waves : State the three main mechanisms responsible for attenuation of ultrasonic waves in a transmission medium.
Assynchronous transmission and synchronous transmission : Explain the difference between assynchronous transmission and synchronous transmission system as used in digital transmission of data.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much energy does the wave carry through the window

The wave passes perpendicularly through an open window, the area of which is0.244 m2. How much energy does this wave carry through the window during a 48.9 s phone call

  Find current gain - voltage gain and power gain of amplifier

The load is a 5- Ω resistance. Find the current gain, voltage gain, and power gain of the amplifier. If the power supply has a voltage of 12V and supplies an average current of 2A, find the power dissipated in the amplifier and the efficiency.

  Sketch the output voltage and output current waveform

A single phase cyclo - converter with mid point configuration is use for obtaining an output frequency of one third times the inputfrequency. Turn ratio from primary to upper secondary is 1/1 and tolower secondary is 1/2 .

  Determine the minimum clocking frequency required

Find the longest allowable evaluate time if the decay in output voltage is to be limited to .2V. If the precharge interval is much shorter then the maximum allowable evaluate time, find the minimum clocking frequency required.

  Find the probability for the occurence of each event

three coins are tossed. Describe the following events: A. at least two heads occur. B. At most one head occurs. C. Exactly two heads occur. D. No heads occur Find the probability for the occurence of each event.

  Block diagram construction

Obtain 8*1 multiplexer with a dual 4 line to 1 line multiplexers having separate enable inputs but common selection lines. Use a block diagram construction.

  Determine what is the actual maximum channel capacity

Given the narrow audio bandwidth of a telephone transmission facility, a nominal SNR of 56DB and a distortion level of

  Sketch the current flowing through the plates

Given that the capacitance of the plates is 4 nF, sketch the current flowing through the plates.

  What are the minimum frequency step increment

A PLL frequency synthesizer has a variable -modulus prescaler of M=10/11 and divider ratios of the A and N COUNTERS OF 40 and 260. the reference frequency is 50khz. what are the VCO OUT PUT FREQUENCY and the minimum frequency step increment

  Design circuit to take output from each of five microphones

You've formed a band, despite advice to the contrary. Actually, the band is pretty good except for the fact that the lead singer (who owns the drum set, the microphones, and the garage where you practice) is a bit tone-deaf.

  Meaning of regenerative braking

1. What is the meaning of regenerative braking? 2. What are the advantages of star-delta starter with induction motor 3. Why ELCB can't work if N input of ELCB do not connect to ground?

  What is the magnitude of the repulsive force between

What is the magnitude of the repulsive force between

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd