Determine the sending end voltage and current

Assignment Help Electrical Engineering
Reference no: EM13246936

A three-phase transmission line is 80 mile long and serves a load of 250 MW at 220 KV and 0.8 power factor lagging. The A, B, C, D constants for the line in each phase are:
A=D=0.95 <0.21°
B=46.54 <85° ?
C=0.0021 <90.5° S
a) Determine the sending end voltage and current
b) What is the voltage regulation.
c) What is the efficiency of the transmission line.

Reference no: EM13246936

Questions Cloud

Find the maximum extension of the spring : Two blocks with mass m1=2kg and m2=3kg hang on either side of a pulley. Block m is on an incline at 30 degrees, Find the maximum extension of the spring.
Verify the design analytically and with spice : Design an inverting amplifier with a gain of -12 that has an input impedance that is larger than 100K that can drive a 2K resistive load using bipolar transistors. Verify your design analytically and with SPICE.
Determine the time constants for transient rise and decay : For the Circuit shown below, V1=5V, R1= 20 kiloOhm, R2= 100kiloOhm, and C= 0.1 microF. Assume the switch in the circuit below has been open for a long time. At t=0, the switch is closed and at t=5 sec the switch is re-opened.
Find change in kinetic energy of the block : A block of mass of 4kg is dragged 2m along a horizontal surface by a force F=30N acting on a 53 degree to the horizontal. Find change in kinetic energy of the block
Determine the sending end voltage and current : A three-phase transmission line is 80 mile long and serves a load of 250 MW at 220 KV and 0.8 power factor lagging. The A, B, C, D constants for the line in each phase are: Determine the sending end voltage and current
Determine the resistance of the wire : Copper at 20C has a resistivity of 1.72x10^-8 ohm-m. A potential difference of 2.0V is applied to a 1.00m long copper wire of radius 0.200mm. Find the resistance of the wire
What was the bullets speed with frictionless block : A 1.12 kg block is attached to a horizontal spring with spring constant 3500 N/m. The block is at rest on a frictionless surface. A 10 g bullet is fired into the block, in the face opposite the spring, and sticks.
What is the bayes estimator : What is the Bayes estimator of λ and what is a 95% credible set for λ that WinBUGS outputs
Find out whether a solid forms when solutions : determine whether a solid forms when solutions containing the following salts are mixed. if so write the net ionic equation for the reaction. a)Na3PO4(aq) and AgNO3(aq). b)K2SO4(aq) and Na2CO3(aq). c)Pb(NO3)2(aq) and Na2CO3(aq). d)BaCl2(aq) and KO..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the magnitude and direction of resultant force

The forces 20N,30N,40N,50N and 60N are acting on one of the angular points of a regular hexagon towards the other five angular points taken in order. Find the magnitude and direction of resultant force

  Find the speed of the block after it has slid 190 m

The magnitude of the acceleration of the block is 1.93 m/s^2 (a) Find the coefficient of kinetic friction between block and plane? I got 0.393 but it is wrong. (b) Find the speed of the block after it has slid 1.90 m

  Find total energy stored in the battery of connected bulb

Then find the total energy stored in the battery before it is connected to the bulb. Determine the total amount of charge that has pessed through the wires that connect the battery and the bulb.

  Calculate the density of the manometric fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Calculate the increase in units of decibels

A)An amplifier has an input voltage of 0.5V and an output voltage of 12V.Calculate the increase in unit decibels. B)An amplifer has an input power 2W and an output power of 80W. Calculate the increase units of decibels.

  Explain telephone channels and pcm analysis

Telephone channels and PCM analysis, The analog to digital converter (ADC) used in a telephone system outputs 8 bit words. The digital words are transmitted as a serial stream to form a PCM voice signal

  Determine free electron and hole concentration

(a) Determine free electron and hole concentration.(b) Calculate the effective density of states at valence band, Nv. Given that ni = 1x1010 cm3 and kT = 0.026.

  Explain the function of frequency dial and frequency range

explain the function of frequency dial and frequency range.

  Construct a canonical sum of products expression of output

Suppose you are to construct a logic circuit with inputs {A,B,C} and output {F} The logic is such that "F" is asserted only when "A" or "B" are asserted and "C" is not. First draw and complete the truth table

  What information is possibly being transmitted

Drift velocity the actual (physical) velocity of electrons along the wire. Transmission velocity the rate at which information can be transmitted electronically using conducing wires. How is it possible that the transmission velocity is so much faste..

  Find the location and the value of the third charger

Charges +Q and +3Q are seperated by a distance 2m. A third charge is located such that the electrostatic system is in equilibrium. Find the location and the value of the third charger in terms of Q.

  Find the electric field for all values of z

An electric field E = 10z(hat) V/m exists in air (for which epsilon_r = 1) in the region defined by the equation z > 0. A dielectric medium with epsilon_r = 5 exists in the region defined by the equation z

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd