Determine the saturated hydraulic conductivity of the layer

Assignment Help Civil Engineering
Reference no: EM13307139

In a laminate floor, hydraulic conductivity at the surface is 2X10-3 cm / s. This uniformly reduces 4X10-4 cm / s to a depth of 22 meters. If the water level is about 3 feet below the surface, determine the saturated hydraulic conductivity of the layer. Additionally, how much is the monthly recharge soil infiltration if it has the following parameters of infiltration and assume a rainy month with a total rainfall of 20 in:
fc = 0.2 in/hr
fo = 1.5 in/hr
k = 0.35 hr-1

Reference no: EM13307139

Questions Cloud

Estimate the volume of recharge during the rainy season : A volume of 1.5x106 m3 of water is then pumped out of the aquifer resulting in a decrease of the groundwater level to 208.8 m. Assuming that the water table in the aquifer responds similarly
Remote network implementation plan : Remote Network Implementation Plan
Find any derivation in the grammar plus-times : find any derivation in the grammar PLUS-TIMES for i*(i) and for { i* (i + i) } by using the bottom-up parsing.
Mini case: k-mart : Mini Case: K-Mart
Determine the saturated hydraulic conductivity of the layer : This uniformly reduces 4X10-4 cm / s to a depth of 22 meters. If the water level is about 3 feet below the surface, determine the saturated hydraulic conductivity of the layer.
Is the intersection of these languages context free : is the intersection of these languages context free? Why or why not?
Determine groundwater flow per unit width of the aquifer : The piezometer A is located 4,000 ft south of piezometer B.  Approximately 3,000 ft of piezometer B there is a river with an elevation relative to sea level of about 455 ft.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compare and contrast the formula resulting from each theory

If given a brittle material with a known tensile strength, Sut, and a known compressive strength, Suc, use the four main fracture criteria (MNSC, BCM, MM, and MIIM) to determine the shear stress, tau, in terms of the material properties Sut and Su..

  Determine the shear stress in the water at y

The velocity distribution for water (20 C) near a wall is given by u=a(y/b)^1/6 where a=10m/s, b=2mm, and y is the distance from the wall in mm. Determine the shear stress in the water at y=1mm. [viscosity of water at 20 C = 1.81 x 10^-5]

  What is last year that carbon tetrachloride can be produced

Section 604 of the act lists the phase-out of production of substances that deplete the ozone layer. What is the last year that carbon tetrachloride can be produced

  Determine volume of water on the land in acre-ft

if 25 acres of land recieved 3.5 inches of water from the irrigation district, determine volume of water on the land in acre-ft

  Determine how much sand did driver place in the drum

A truck driver used sand to soak up a 1 g spill of lindane (C6H6Cl6). He placed the contaminated soil in an open drum which then filled with 150 L of water during a rainstorm. You test the water and find a concentration of 17 M/L.

  How many cubic meters of water are needed

Establish a grass cover over a 10ha landfill. The root zone of the grass is 40cm deep. Increase the volumetric water content of root zone from 12% to 24%. How many cubic meters of water are needed?

  Determine the heights of the fluid columns for barometers

Determine the heights of the fluid columns for barometers that use the following liquids at 20 C: water, ethyl alcohol, and mercury. Why do you think mercury barometers were used in the past (before the negative health effects of mercury were know..

  Of which the shape is described by the equation r

The double collar B is pin-connected together such that one collar slides over the rotating rod and the other slides over the horizontal curved rod, of which the shape is described by the equation r= 1.5(2-cos)

  What is the carbon concentration at 4 mm below surface

A 1045 steel will be heat treated in air at 900 C. What is the carbon concentration at 0.4 mm below the surface after 6 hours

  Explain why the compressive strength of wood loaded

EXPLAIN BRIEFLY WHY THE COMPRESSIVE STRENGTH OF WOOD LOADED "PARALLEL" TO ITS GRAIN IS HIGHER THAN THE COMPRESSIVE STREGTH OF THE SAME WOOD LOADED "PERPENDICULAR" TO THE GRAIN

  Determine using energy methods speed of crate after moving

The coefficient of friction between the crate and the floor is µs = 0.4 and µk = 0.3. If P is slowly increased until the crate starts to move and then remains constant, determine using energy methods the speed of the crate after moving 2 m.

  Determine what is angular error if the distance to the pole

A 6-ft range pole is set over a station on which a sight is to be made with a the odolite. If the sight is made to the center of the rod 4-ft up from the ground, and the center of the top of the pole is out of plumb 0.12 feet in a direction normal..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd