Determine the resultant force of the water on the gate

Assignment Help Mechanical Engineering
Reference no: EM131306934

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts.

2. A long, vertical wall separates seawater from fresh water. If the seawater is 7 m deep, what depth of freshwater is required to yield a zero resultant force on the wall? When the resultant force is zero, will the net moment on the wall due to fluid forces also be zero? Explain.

Reference no: EM131306934

Questions Cloud

What are the biggest barriers to wide scale adoption : What do you think are the biggest barriers to wide-scale adoption of m-commerce by consumers? Who do you think is working on solutions to these problems and what might the solutions entail?
What is pattern seen in ice core records of carbon dioxide : What is the pattern seen in the ice core records of carbon dioxide and temperature in terms of high and low periods over the past hundreds of thousands of years (before modern human history?
What is the pressure inside the tank : The water level in the other side of the U-tube, open to the atmosphere, is 2 ft above the base. What is the pressure inside the tank
Prepare a variance analysis between budgeted : Prepare a variance analysis between budgeted and actual figures - List the discrepancy and analyse it as a positive or negative one Locate the area and give at least 5 reasons why the discrepancy may have occurred
Determine the resultant force of the water on the gate : A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts.
An investor with good knowledge of companys past record : As an investor with a good knowledge of the company's past record, to what extent do you attribute its performance problems to problems in its corporate governance?
Describe groundwater management challenges : Describe groundwater management challenges. Include in your description the types and sources of contamination, overdrawing and its effect on the water table.
Discuss the ethical dilemmas that this request raises : This will help them confirm or deny that this company is selling equipment that is used directly in the torture of political prisoners. Discuss the ethical dilemmas that this request raises and how you would react to this request.
What steps should microsoft take to retain its most valuable : Adopting a cautious stance, Microsoft strategists have not aggressively promoted its free-product offering. Some experts argue that Microsoft should be taking the defection among price-sensitive customers more seriously. Agree or disagree? Support..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The heat addition in both combustion chambers is reduced

a gas turbine operates with a regenerator and two stages of reheating and intercooling. this system is designed so that

  After the pressures but not the temperature in the two

an isolated chamber with rigid walls is divided into two equal compartments one containing steam at 10 bar and 370oc

  A body initially at rest is accelerated to a velocity of

a body initially at rest is accelerated to a velocity of 200ms along the surface inclined at 30 degrees relative to

  Find the maximum tensile strength of the composite you may

a unidirectional fiber composite consists of 60 by volume of continuous type-1 carbon fibers in a matrix of epoxy. find

  Determine the force f required to pull the shaft

The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic viscosity of 8.0 ×10-4 m2/s and a specific gravity of 0.91. Determine the force F required to pull the shaft at a velocity of 3 m/s. Assume the velo..

  Compute the design factor of a rod that is under a tensile

compute the design factor of a rod that is under a tensile load of 3125 lb. the rod is rectangular 1.5 in by 3.5 in and

  What is the heat transfer per unit length of tube

What is the heat transfer per unit length of tube to Refrigerant-134a at 240 K - explore the effect on qc" of variations in heat sink design and operating conditions.

  Air expands through a turbine operating at steady state on

air expands through a turbine operating at steady state on an instrumented test stand. at the inlet p1 160 lbfin2 t1

  Compute the drag force exerted on the car

A wing on a race car is supported by two cylindrical rods, as shown in Fig. 17.15. Compute the drag force exerted on the car due to these rods when the car is traveling through still air at - 20°F at a speed of 150 mph.

  Calculate the heat lost per square meter area of the furnace

Calculate the heat lost per square meter area of the furnace wall and also find outside surface temperature.

  Determine the rate of energy transfer from the air to water

Water enters one stream of an unmixed stream heat exchanger at 20°C and increases in temperature by 10°C. Air enters the second stream on the heat exchanger at 400°C and 5 kg/s. The air temperature at the exit of the heat exchanger is 200°C cooler th..

  Calculate the magnitude and direction of the velocity

Calculate the magnitude and direction of the velocity of the fluid leaving the vane - the thrust on the vane in a horizontal direction

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd