Determine the required value for m

Assignment Help Civil Engineering
Reference no: EM13210658

A 1 meter diameter cylindrical mass, M, is connected to a 2 meter wide rectangular gate. The gate is to open when the water level, h, drops below 2.5 meters. Determine the required value for M. Neglect friction at the gate hinge and pulley.

Reference no: EM13210658

Questions Cloud

Draw all aldehyde and ketone isomers of c6h12o : What is the reaction that occurs with hexanal and propanol (give both the hemiacetal and acetal products)?
What is the distiniction b/n point and non point sources : what is the distiniction b/n point and non point sources of water pollution and thier varation with surface and ground water?
"describing two approaches-indicators to measuring patient : "Describing two approaches or indicators to measuring patient outcomes. Measuring the quality of care is essential to being able to identify which areas of patient care need improvement.
Calculate the npv according to the divisional manager : Calculate the NPV according to the divisional manager and the NPV incorporating inflation levels to support your comments. In both cases, assume the total investment in working capital will be recovered at the end of the project.
Determine the required value for m : A 1 meter diameter cylindrical mass, M, is connected to a 2 meter wide rectangular gate. The gate is to open when the water level, h, drops below 2.5 meters. Determine the required value for M. Neglect friction at the gate hinge and pulley.
Determine the bod : A Biodegradable industrial wastewater (paper production) has a COD of 600 mg/L. If the BOD progression follows first-order kinetics with a rate constant = 0.10 per day, determine the BOD.
Belief perseverance-functional fixedness : belief perseverance, functional fixedness, representative heuristics, confirmation bias, OR framing?
Explain what reaction conditions can change : What is the minor product? Explain why the one product is formed preferentially over the other. What reaction conditions can you change to favor the formation of the minor product?
Determine the cod : Determine the COD, carbonaceous BOD, and nitrogenous oxygen demand of a 100 mg/L solution of urea (N2H4CO)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculating largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture.

  Width of the footing if factor of safety given

Characteristic values of the shear strength parameters of the soil are c'= 0, and f' = 400. Determine the required width of the footing if a factor of safety of 3.0 against shear failure is specified when the water table rise to foundation level.

  Supervisors technicians and skiled workers in dangerous work

As a project manager on site where work for 3 km long tunnel has been undertaken the site is remote and takes about 2 days to travel to nearest town supervisors technicians and skiled workers in dangerous work.

  Compare and contrast the purpose and scope

Compare and contrast the purpose and scope of the Federal Insecticide, Fungicide, and Rodenticide Act with the provisions of the Federal Food, Drug, and Cosmetic Act.

  Heat exchanger second-law efficiency

The condenser in a refrigerator receives R-134a at 700 kPa and 50C, and it exits as saturated liquid at 25 C, The flow rate is 0.1 kg/s,and the condenser has air in at an ambient temperature of 15 C and leaving at 35 C. Find the minimum flow rate ..

  Define mechanical engineering dynamics

Important information about Mechanical engineering dynamics, A 3000 lb car rests on a horizontal street out of gas with its brakes locked.

  Hydrograph for a watershed having a drainagearea

For the data given below, derive the 2-hr unit hydrograph for a watershed having a drainagearea of 216 km^2, assuming a constant baseflow of 20 m^3/s.

  Calculating sand shear strength

Estimate the effective friction angle for the sand (assume c' = 0). Calculate the sand's shear strength (τf) on a horizontal plane at depths of the 20 ft and 50 ft.

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  Maximum and minimum stress intensities in the section

Determine the maximum and minimum stress intensities in the section.

  Comparative analysis of the types of safeguards

Provide a comparative analysis of the types of safeguards would you suggest for the company's information system.

  Importance of mineral identification in applications

What are minerals? Sketch different types of mineral crystal forms and list different types of rock forming minerals. Describe with examples the importance of mineral identification in engineering applications.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd