Determine the required gauge pressure for the inlet plenum

Assignment Help Mechanical Engineering
Reference no: EM13641561

A heat exchanger for cooling electronic components is fabricated with two aluminum plates separated by aluminum fins (rather like corrugated cardboard). The plates are 8.04 inches wide by 10 inches long and 0.60 inches thick. Each plate has a heat load of 100 watts. There are 73 fins, each 0.80 inches high by 10 inches long and 0.010 inches thick. The fins are spaced on 0.110 inch centers. Room air at a rate of 250 ft3/min is delivered by a fan to a plenum at the inlet end of the heat exchanger. The air discharges from the heat exchanger into the room where the temperature is 68°F and the absolute pressure is 29.92 inch-Hg. Determine the required gauge pressure for the inlet plenum, assuming all surfaces are smooth and the loss coefficients (based on tube velocity) for the inlet and outlet are 0.7 and 0.6, respectively.

Reference no: EM13641561

Questions Cloud

A 38 kg fish swimming 13 ms swallows an absent minded 14 kg : a 3.8 kg fish swimming 1.3 ms swallows an absent minded 1.4 kg fish swimming toward it at a velocity that brings both
Write down equations relating the temperature and volume of : a liquid piston stirling engine is shown below. assume that the gas contained in the two sealed pistons is a true ideal
If the experiment is repeated at the same temp but greater : a mass of ccl4 is vaporized at 100.0 c to fill a flask with 275.0 ml when the atmospheric pressure is 753.9 torr. if
A how much energy in calories is transferred to the water : a 190 g copper bowl contains 180 g of water both at 23.0degc. a very hot 450 g copper cylinder is dropped into the
Determine the required gauge pressure for the inlet plenum : a heat exchanger for cooling electronic components is fabricated with two aluminum plates separated by aluminum fins
While riding on a ferris wheel at the state fair you are : while riding on a ferris wheel at the state fair you are seated 10 m from the axis. if you make a complete rotation
If the period of contact between the ball and the club was : a 50-grams golf ball is hit with a club. if the initial velocity of departure of the ball is 40 ms what is the impulse
A person is exercising burning 550 calhr while doing this : a person is exercising burning 550 calhr. while doing this exercise they breath deeply so the volume they take into and
Calculate the energy values and degeneracies of the lowest : calculate the energy values and degeneracies of the lowest three energy levels of an electron confined to move in a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd