Determine the required diameter d of the bar

Assignment Help Mechanical Engineering
Reference no: EM131062594

A steel bar of solid circular cross section and length L= 2.5 m is subjected to an axial tensile force T= 24 kN and a bending moment M = 3.5 kN m (see figure).

(a) Based upon an allowable stress in tension of 110 MPa, determine the required diameter d of the bar; disregard the weight of the bar itself.

(b) Repeat (a) including the weight of the bara

1014_079626e1-dcbf-4589-ae56-32df8cb8ce3b.png

Reference no: EM131062594

Questions Cloud

Structural theory of sociology : What were the achievements of Emile Durkheim relating to the structural theory of sociology
Class or writing down troublesome vocabulary : What differences in student approach to English do you anticipate when working with students who speak a Latin or Germanic language versus students who speak Japanese, Chinese or Arabic?
Make a journal entry for each of the given transactions : Please make a journal entry for each of the transactions. Remember that the revenues must be classified as unrestricted, temporarily restricted, or permanently restricted.
Major issues of health from a structural perspective : (1) Identify and discuss some major issues of health from a structural perspective.
Determine the required diameter d of the bar : Based upon an allowable stress in tension of 110 MPa, determine the required diameter d of the bar; disregard the weight of the bar itself.
Health disparities between different races : How might racism (institutional & individual) contribute to financial inequalities and also health disparities between different races? Provide 2 or 3 examples. at least 150 words
Discuss the judicial selection process of state : Discuss the judicial selection process of your state. Include, at a minimum, the qualifications and steps that are taken in order to select judges for the different kinds of courts within your specific state.
Calculate the maximum tensile and compressive stresses : Calculate the maximum tensile and compressive stresses σt and σc, respectively, at the base of the tree due to its weight.
Products of nurture : Sociologists argue that we are products of nurture (i.e. socialization). Thus, had we been born into a different family, a different part of the world, a different race, gender, sociology-economic class etc.,

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Air at a rate of 10 lbms enters an adiabatic compressor at

air at a rate of 10 lbms enters an adiabatic compressor at 15 psia 80 f and leaves at 150 psia 740 f. calculate the

  Final temperature of the steam and the volume of the vessel

An insulated vessel has two compartments separated by a membrane. On one side is 1 kg of steam at 400 oC and 200 bar. The other side is evacuated. The membrane ruptures filling the entire volume. The final pressure is 100 bar. Determine the final tem..

  What are the possible failure modes for the shaft that must

a rotating shaft has power transferred into a gear at b by a bevel gear resulting in a steady radial force f1100lb and

  A 60-lb uniform thin panel is placed in a truck with end a

a 60-lb uniform thin panel is placed in a truck with end a resting on a rough horizontal surface and end b supported by

  For the refrigerant as the system w -056 btu kinetic and

refrigerant 134a is compressed with no heat transfer in a piston- cylinder assembly from 30 lbfin2 20 degrees f to 160

  The 2-lb box has a velocity of 5 fts when it begins to

the 2-lb box has a velocity of 5 fts when it begins to slide down the smooth inclined surface at a. the coordinates of

  A force of 100 lbf at -30 degrees to the right of the

a mass of 100 slug is towed by 2 ropes one rope pulls with a force of 200 lbf at 30 degrees to the left of the centar

  The compression ratio is 135 and the maximum pressure is 50

in a dual cycle the heat added at constant volume is equal to the heat added at constant pressure. the compression

  Find number of independent dimensionless parameters

Pressurised tank drained through a smooth nozzle, area A m(dot) = m(dot)(del p ,h, row, A, g) Find: number of independent dimensionless parameters. obtain the parameters

  Explain midrange and amplitude components

Midrange and amplitude components, A shaft is subjected to a completely reversed bending stress such that Xmax=40kpsi and Xmin=-40kpsi

  Determine the turbine inlet temperature

Determine the turbine inlet temperature, the cycle thermal efficiency, and the back-work ratio of this cycle.

  The tension t is increased in such a way that the string is

a 1-kg disk slides on a smooth horizontal table and is attached to a string that passes through a hole in the table.a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd