Determine the required capacity of the motor of the

Assignment Help Civil Engineering
Reference no: EM13531121

A step-type escalator as shown is designed to transport 120 persons per minute at a constant speed v=1.5 ft/s. The overall efficiency of the escalator is estimated to be 70%, and a 200% overload is to be allowed. Assuming that the average weight per person is 160lb, determine the required capacity of the motor of the escalator. The escalator is 15ft high and has a 30 degree angle with the horizon.

Reference no: EM13531121

Questions Cloud

Do the same for saturated vapor steam in an adiabatic : Saturated liquid water is in an adiabatic compressor with inlet and outlet pressures of 100 kPa and 1 Mpa. The isentropic efficiency is 85%. Find the work input (kj/kg) and entropy generation (kj/ kg K).Do the same for saturated vapor steam in an adi..
What is the density of the rock before it blasted : You are given the following information about a dry-batchpaving operation. You are going to use one mixer that has a servicerate of 30 serives/hr. The dry-batch trucks you use forbringing concrete to the paver have an arrival rate of 7.5 arrivals/hr...
A street car line on the center of an 80 ft street makes : A street car line on the center of an 80 ft street makes a 75degrees 24' turn into another street of equal width. Thecorner curb line has R=12 ft. What's the largest R that canbe given a circular curve for the tract center line if the law requires it..
Knowing that the coefficient of restitution between the : A 2-lb sphere A is moving to the left with a velocity of 40 ft/swhen it strikes the inclined surface of a 5-lb block B which is atrest. The block is supported by rollers and is attached to a springof constant k=12 lb/in.
Determine the required capacity of the motor of the : A step-type escalator as shown is designed to transport 120 persons per minute at a constant speed v=1.5 ft/s. The overall efficiency of the escalator is estimated to be 70%, and a 200% overload is to be allowed. Assuming that the average weight per ..
What is the underflow flow rate : A settling tank in a water treatment plant has an inflow of 2m3/min and a solids concentration of 2100 mg/L. The effluentfrom this settling tank goes to sand filters. Theconcentration of sludge coming out of the bottom (the underflow) is18,000 mg/L, ..
The mass flow rate of the refrigerant and : Refrigerant R-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at 120 kPa with a quality of 20 % and leaves at 120 kPa and -20°C. If the compressor consumes 450 W of power and the COP is 1.2
Determine how much money the home owner would have saved : A house that was heated by electric resistance heaters consumed 1200 kWh of electric energy in a winter month. If this house were heated by a heat pump that has an average COP of 2.4, determine how much money the home owner would have saved that mont..
Consider the process of baking potatoes in coventional oven : Consider the process of baking potatoes in coventional oven.Can the hot air in the oven be treated as a thermal energyreservoir? Explain

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the emissions of heat-trapping carbon dioxide

Emissions of heat-trapping carbon dioxide (CO2) reached an all-time high of 31.6 gigatons in 2011, a 3.2% increase over 2010. The International Energy Agency said this further reduces the chance that the world can avoid a dangerous rise

  Estimate maximum outlet velocity that system could deliver

couplings , each with a loss coefficient of k=0.15, are located every 10 m along thehose. the nozzle outlet diamter is d= 25 mm, its minor losscoefficient is k=0.02 based on outlet velocity

  Determine the critical load of a round wooden dowel

Determine the critical load of a round wooden dowel that is 0.9m long and has a diameter of (a) 10mm (b) 15mm. Use E=12GPa

  Determine what is the amount of the annual withdrawl

$25,000 is deposited in a savings account that pays 10% interest, compounded monthly. Equal annual withdrawls are to be made from the account, beginning one year from now and countinuing forever.

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m

  How much atrazine is bound to soil and dissolved in water

Atrazine is adsorbed to a soil that is only saturated by 5%(i.e. only a twentieth of the pore volume is filled with water), how much atrazine is bound to the soil, dissolved in the water, and present as vapor in the gas phase

  Determine the distance downwind to reach the maximum so2

A 45-percent efficient, coal-fired power plant generates output power of 1000 MW (106 kW) and emits SO2 at the legally allowable rate of 0.6 lb SO2 per million BTU of heat into the plant. The stack has an effective height of 250 m.

  Compute evaporation rates in the winter and in the summer

At a certain location during the winter, the average air temperature is 10 degrees celcius and the net radiation is 40W/m^2 and during the summer the net radiation is 200W/m^2 and the temperature is 25 degrees celcius.

  Calculate the average headways and spacing at maximum flow

By assuming a linear speed-density relationship, the mean free flow speed on a highway facility lane equals 65 mph. The jam density is observed to be about 170 vpm. 1. Plot the q-k-u curves

  How do you find the maximum axial load using asd

An 8x12 column of No. 1 Spruce-Pine-Fir(South) has an unbraced length for buckling about the strong x axis of 16 feet and an unbraced length for buckling about the weak y axis of 8 ft. Cm = 1.0 and Ct = 1.0

  Find the total weight mobilised

Determine the minimum weight of concrete and calculate the actual weight of concrete - Find the total weight mobilised

  Spreader beam and hoisted by a crane

The 3.5mg engine is suspended from a 500 kg spreader beam and hoisted by a crane which gives it an acceleration of 4m/s^2 when it has a velocity of 2m/s. determine the force in chains AC and AD during the lift.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd