Determine the reduction in the exit temperature of the

Assignment Help Mechanical Engineering
Reference no: EM13614478

The compression stages in the axial compressor of the industrial gas turbine are close coupled, making intercooling very impractical. To cool the air in such compressors and to reduce the compression power, it is proposed to spray water mist with drop size on the order of 5 microns into the air stream as it is compressed and to cool the air continuously as the water evaporates. Although the collision of water droplets with turbine blades is a concern, experience with steam turbines indicates that they can cope with water droplet concentrations of up to 14 percent. Assuming air is compressed isentropically at a rate of 2 kg/s from 300 K and 100 kPa to 1200 kPa and the water is injected at a temperature of 293 K at a rate of 0.2 kg/s, determine the reduction in the exit temperature of the compressed air and the compressor power saved. Assume water vaporizes completely before leaving the compressor, and assume an average mass flow rate of 2.1 kg/s throughout the compressor.

Reference no: EM13614478

Questions Cloud

Calculate the power required to run the refrigerator : the fluid used is r-134a. the flow of r-134a is 70 lbmmin. if r-134a enters a compressor at -10 deg f and is a
Given below are two applications of statistics descriptive : given below are two applications of statistics descriptive and inferential. choose what type of application is being
Determine the values of the friction factor corresponding : chemical civil and mechanical engineers must often determine the power required to pump a fluid through a series of
Widgets inc uses the straight-line method to depreciate : widgets inc uses the straight-line method to depreciate assets in determining its finacials profit. widgets also
Determine the reduction in the exit temperature of the : the compression stages in the axial compressor of the industrial gas turbine are close coupled making intercooling very
As reported by a spokesperson for southwest airlines the : as reported by a spokesperson for southwest airlines the no-show rate for reservations is 16. in other words the
Big lake boat tours sold off one of their tour boats that : big lake boat tours sold off one of their tour boats that was toosmall to meet the current needs of business.the boat
Consider a normal distriubtion with mean 5 and standard : consider a normal distriubtion with mean 5 and standard deviation 2a. sketch the associated normal curveb. write the
The refrigerant leaves the condenser at 07 mpa 26 degc : consider a non-ideal vapor-compression cycle where refrigerant 134a flows at a rate of 0.05 kgs. the refrigerant enters

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd