Determine the rate of heat transfer in the heat exchanger

Assignment Help Mechanical Engineering
Reference no: EM13711750

A heat exchanger is to heat water (Cp= 4.18 KJ/Kg.C ) from 25 to 60 C at rate of 0.2 kg/s. the heating is to be accomplished by geothermal water ( Cp= 4.31 KJ/Kg.c ) available at 140C at a mass flow rate of 0.3Kg/s. Determine the rate of heat transfer in the heat exchanger and the exit temperature of geothermal water.

Reference no: EM13711750

Questions Cloud

Is triple-bottom-line accounting a reasonable approach : 3. Is triple-bottom-line accounting a reasonable approach to encourage businesses to take responsibility for the impact of their actions on social and environmental systems, or does it place an unrealistic burden on businesses to measure what may ..
Determine the mass flow rate of propane : A typical gas stove burner supplies a kettle filled with water at a rate of 15,000 Btu/hr with a flame temperature of 750C. The gas fed to the burner is composed of propane mixed with 10% excess air. The gas feed is initially at -20C and 1 bar and th..
What is the mole fraction of water in the exhaust stream : A mixture of propane and butane is fed into a furnace where it is mixed with air. The furnace exhaust leaves the furnace at 343°C, 780.0 mmHg and contains only N2, O2, CO2, and H2O. The partial pressure of O2 in the exhaust is 51.40 mmHg and the part..
The mole fraction of water vapor in the air : If the weather report says that it is 60°F outside, the barometric pressure is 28.50 in Hg, and the relative humidity is 85.0%, find the following values. The partial pressure of water. The mole fraction of water vapor in the air
Determine the rate of heat transfer in the heat exchanger : A heat exchanger is to heat water (Cp= 4.18 KJ/Kg.C ) from 25 to 60 C at rate of 0.2 kg/s. the heating is to be accomplished by geothermal water ( Cp= 4.31 KJ/Kg.c ) available at 140C at a mass flow rate of 0.3Kg/s. Determine the rate of heat transfe..
Coca-cola blak was introduce to various international market : Coca-Cola Blak was introduced to various international markets including the USA and discontinued in the US market in 2007. In this case you are to analyze a famous firm's product failure and in doing so demonstrate your understanding of a prom..
Determine the temperature at the compressor exit : Air is compressed from 14.7 psia and 60 F to a pressure of 150 psia while being cooled at a rate of 10 Btu/lbm by circulating water through the compressor casing. the volume flow rate of the air at the intel conditions is 5000 ft^3/min, and the power..
Composed of mutuality orthogonal unit vectors : Let A, B, C and D denote four reference frames, composed of mutuality orthogonal unit vectors ai, bi, ci and di (i=1,2,3), respectively. Assume that rotation matrices aRc, aRd and bRd are given. Let x, y, z and t denote some specified constants. Give..
Calculate the wall shear stress : State mathematically Newtona's law of viscosity. Water moves over a flat surface. At a point on the surface the velocity gradient is 60 s-1. The viscosity of water is 0.0012 Ns/m2. Calculate the wall shear stress.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A diesel cycle operates with a compression ratio of 15 and

1. a diesel cycle operates with a compression ratio of 15 and a cutoff ratio of 2.5. what is the rate of heat input

  The steam line leading to the turbine inle

The steam line leading to the turbine inle

  Assignment 1problem 1determine the analytical solution for

assignment 1problem 1determine the analytical solution for the maximum stress of the beam shown compare with stress

  Estimate the diffusion coefficient at 25degc of trace of

estimate the diffusion coefficient at 25degc of trace of ethanol in water and of traces of water in ethanol. viscosity

  At a point on the free surface of a machine part the

at a point on the free surface of a machine part the strains are ex1200 mu ey300mu yxy700 mu. use mohrs circle to

  Stainless steel rod with circular cross section has length

A stainless steel rod with a circular cross section has a length of 100 mm and a diameter of 2.0 mm. It is deformed elastically in compression by a force of 500 N applied parallel to its length. The material has a Young’s modulus of 200 GPa, and a sh..

  Etermine the force applied by the ram

A cube of 2" dimensions is placed in a square hole (also of 2" dimensions) that is 1.998" deep. The hole was cut out of a rigid material. (The top of the cube protrudes .002" above the surface). If a flat rigid plate is placed on top of the cube and ..

  Analyse the stability of the closed loop system

Find the closed loop transfer function Gcl(s) = θL(s)/ θs(s) and determine the initial and final values of θL(t) for a step input θc(t).

  The water exit the firehose with sufficient velocity to

water exits the firehose into atmosphere of 101kpa. the water exit the firehose with sufficient velocity to travel 30

  Question 1 a mild steel bar 40 mm diameter and 100 mm long

question 1. a mild steel bar 40 mm diameter and 100 mm long is subjected to a tensile force along its axis.youngs

  Wheel cart hooked with two springs

A wheel cart hooked with two springs is subjected to an impulsive dynamic force for the time duration of 0.5 seconds. Develop a Matlab script based on while loop to determine the response X for the first three seconds based on time increment 0.01. Pl..

  Write the matlab solution for the ode using the fourth

a u-tube manometer is initially filled with water but exposed to a pressure difference such that the water level on the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd