Determine the rate of heat transfer from the balls to air

Assignment Help Civil Engineering
Reference no: EM131031469

Consider a 1000-W iron whose base plate is made of 0.5-cm-thick aluminum alloy 2024-T6 (p= 2770 kg/m3 and cp 875 J/kg · °C). The base plate has a surface area of 0.03 m2. Initially, the iron is in thermal equilibrium with the ambient air at 22°C. Assuming 85 percent of the heat generated in the resistance wires is transferred to the plate, determine the minimum time needed for the plate temperature to reach 140°C.

1217_1e4abfe1-424f-45b6-9e27-3bdb78845986.png

Reference no: EM131031469

Questions Cloud

Technical term for independent trials : Use the Probability applet or statistical software to simulate 100 free throws shot by a player who has probability 0.75 of making each shot. (In most software, the key phrase to look for is "Bernoulli trials." This is the technical term for indep..
Reliability of the pinch test : What would what would Descartes conclude about the reliability of the pinch test?2.Exactly why would he conclude this?
Compare a compensation plan you are familiar and sas : Specifically, you will compare a compensation plan you are familiar with to that of Microsoft and SAS. Read and follow the instructions for Mapping Compensation Strategies SEE ATTACHED.
Which of the following controls would be : Which of the following controls would be the most appropriate means to ensure that terminated employees are removed from the payroll?a) Mailing all checks to individual employee home addresses.b) Requiring direct deposit of all payroll checks.c) Reco..
Determine the rate of heat transfer from the balls to air : Assuming 85 percent of the heat generated in the resistance wires is transferred to the plate, determine the minimum time needed for the plate temperature to reach 140°C.
Difference between the count of heads : Keep going. Stop at 240 tosses and again at 480 tosses to record the same facts. Although it may take a long time, the laws of probability say that the proportion of heads will always get close to 0.5 and also that the difference between the count..
Describe the sophists : Which of the following most accurately describe the sophists They were empiricist rather than pragmatist They believed that truth was subordinate and subservient to power
What was the definition of motion according to aristotle : What was the definition of motion according to Aristotle?
Aristotle proposed a fifth element : Aristotle proposed a fifth element, aether, in addition to the four proposed earlier by Empedocles.name four elements proposed earlier

Reviews

Write a Review

Civil Engineering Questions & Answers

  Deisgn a thrust block needed to resist the force generated

Deisgn a thrust block needed to resist the force generated by a 45 degree flanged regular elbow which carries a flow of 14 cfs.  The diameter of the fitting narrows from 24 inches to 18 inches and the inlet pressure is 100 psi.

  Calculate what will be the total emissions of pm and pm10

emissions from waste oil combustion may be estimated using ap-42 1.11. A small boler is operated from 10/15/2012 through 4/15/2013 and it is used to burn 45 gallons per hour of a blended waste oil having an ash content of 7%

  What do you think is the best ratio of b/y to use in your

A canal of rectangular cross-section and an n=0.030 is to be laid on a slope of 0.002 and is to carry a discharge of 30 m3/s. Calculate the cross-sectional area required for the channel to carry this flow based on the norma

  Determine the work done in the compression process

Methane is compressed in a piston-cylinder device from initial pressure of 110 kPa and an initial temperature of 25 oC to a final pressure of 1,00 MPa. The compression process is polytropic with n = 1 .10.

  How far does each skater travel

If they pull themslevles along the the rope until they meet how far does each skater travel? B)If only the 45 kg skater pulls along the rope until she meets her friend( who just holds onto the rope) how far does each skater travel?

  Determine the ultimate bod and 5-day bod of the sample

A result of a 7-day BOD test performed on a sample from anoligotrophic lake was 10 mg/L. The base 'e' BOD rate constantdetermined from previous studies was estimated to be 0.10d-1.

  What should be the design capacity of the distribution pipes

A water supply system is being designed to serve a population of 200,000 people with an average per-capita demand of 600L/Person-day (peak demand factor is 1.8) and a needed fire flow of 28,000 L/min.

  Determine the pumping power required to produce of water

In an irrigation system sometimes water must be pumped over long distances. Consider a system that consistes of a 1 m diameter, 2 km long commercial steel pipe, which connects a river to an irrigation canal.

  Find the mean value of the time rate of change of the

Gas is flowing in a long 9-in-diameter pipe from A to B. At sectionA the flow is 0.65 lb/sec while at the same instant at section Bthe flow is 0.72 lb/sec. The distance between A and B is 750 ft.

  Determine what volume of naocl will be needed

An electric power plant consumes 2.5 million gallons per day of cooling water. To control bacterial growth (slime), 2.0 mg/L of chlorine (measured as Cl2) is injected into the make-up water fed to the system.

  Determine the outer surface temperature and the rate of heat

Considering both radiation and convection heat transfer, determine the outer surface temperature and the rate of heat transfer though the roof.

  Find the volume of the material using force equilibrium

Your engineering consulting firm has been asked to determine the specific weight of an unknown material. You decide to use the concept of buoyancy to figure this out. So you weigh the material in both air and water.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd