Determine the pressure that develops in the container

Assignment Help Civil Engineering
Reference no: EM13555029

A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature. Assume that the volume of the container remains constant and the value of the bulk modulus of the water remains constant and equal to 300,000psi.

Reference no: EM13555029

Questions Cloud

Estimate what is the cylinders initial potential energy : A 3.0-kg cylinder falls vertically from rest in a very tall, evacuated tube 20m above the surface of the earth. what is the cylinder's initial potential energy
What is the pressure of the gas at the new volume : Suppose 23.8 L of an ideal monatomic gas at a pressure of 2.60 105 kPa is expanded adiabatically (no heat transfer) until the volume is tripled. What is the pressure of the gas at the new volume
What is the footballs change in momentum : A football player kicks a 0.41-kg football initially at rest;and the ball flies through the air. what is the football's change in momentum
What is the maximum speed of the goldfinch : A 30.0- goldfinch lands on a slender branch, where it oscillates up and down with simple harmonic motion of amplitude 3.50×10?2 and period 1.50. What is the maximum speed of the goldfinch
Determine the pressure that develops in the container : A rigid-walled cubical container is completely filled with water at 40 0F and sealed. The water is then heated to 100 0F. Determine the pressure that develops in the container when the water reaches this higher temperature
Draw a mass balance diagram and estimate the monthly mass : Each month the speedy dry Cleaning company buys 1 barrel (0.160 m^3)of dry cleaning fluid . Ninety percent of the fluid is lost to the atmosphere and 10 percent remains as residue to be disposed of
Determine how many rpms is it doing : You rev your car's engine to 2600 (). a) If you change the period of the engine to 0.038 , how many rpms is it doing
What is the maximum acceleration from rest for the car : A newly designed car has a 9.0 ft wheelbase, is rear wheel drive, and has a center of gravity 18 inches above the road and 4.3 ft behind the front axle. the car weighs 2450 lb, the mechanical efficiency of the drivetrain is 90% and the wheel radius i..
What are the recorded values of r dot : At the bottom of a loop in the vertical plane an airplane has a horizontal velocity of 315 mi/h and is speeding up at a rate of of 10ft/s^2. The radius of curvature of the loop is 1mi

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the final temperature of the system

A 100 gram piece of ice cooled at -20 degrees Celsius is placed in the calorimeter. What is the final temperature of the system, and what mass of ice and water remains

  Determine the radial dimension r as a function of z

The pedestal supports a load P at its center. If the material has a mass density p, determine the radial dimension r as a function of z so that the average normal stress in the pedestal remains constant.

  Determine what would be the maximum possible percent

Engineers at the General Electric turbine division are trying to improve an existing adiabatic steam turbine that receives 100 kg/s superheated steam at 10 MPa and 800 oC and after expansion and producing power, the spent steam exits the turbine at 1..

  Determine what is the ice point of water in the scale

Devise an absolute temperature scale where the boiling point of water at 1 atmosphere (101 kPa) pressure = 100 degrees in your scale. What is the ice point of water in your scale

  Determine the rotation of the gear at e

The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B

  Determine the minimum entropy change of the thermal energy

Heat is now added until the quality is 40 percent. Determine the minimum entropy change of the thermal energy reservoir supplying this heat.

  Compute the maximum service

Compute the maximum service (unfactored) concentrated live load that can be applied at 1ft from the free end of the cantilever. Use load and strength -reduction factors from ACI Code Sections 9.2 and 9.3. Also check As,min.

  Determine horizontal and vertical components of the force

The window is to be bolted onto the vertical wall of the pool and faces outward, covering a 2ft diameter opening in the wall. The venter of the opening is 4ft below the surface.

  Determine the ratio of the weight of the solid shaft

Two shafts are made of the same material and are of equal lengths.one of them is solid and another one is hollow. the ratio of inside and outside diameters for hollow shaft is 0.65.

  Write mass balance equation for an ideal 1d plug-flow stream

Assume the rate constant for BOD decay is 0.2 d^-1, the mean velocity of the stream is 0.5 m s^-1, and the initial concentration is 100 mg L^-1 at x=0. Plot the resulting concentration with downstream distance x in km.

  Find the total head loss if the flow velocity is 4 fps

one open globe valve, one medium-radius elbow, and one 90 degrees pipe bend (kb=0.13) with a radius of curvature of 45 in. The length of the bend is not included in the 110 ft.

  Determine the centroid-moment of inertia and section modulus

THE HOME DEPOT IN RED HOOK ,BROOKLYN IS LOOKING TO RENOVATE THEIR STEEL ROOF TRUSS.YOU HAVE BEEN ASKED TO DETERMINE THE CENTROID,MOMENT OF INERTIA,SECTION MODULUS AND RADIUS OF GYRATION OF THE DOUBLE ANGLE.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd