Determine the pressure kpa at the start and end of

Assignment Help Mechanical Engineering
Reference no: EM13629759

Six kilograms of carbon dioxide in a piston-cylinder device execute a Carnot cycle consisting of the following four processes.

Process 1-2: Adiabatic compression

Process 2-3: Isothermal heat addition

Process 3-4: Adiabatic expansion

Process 4-1: Isothermal heat rejection

The minimum and maximum gas temperatures are 300 K and 900 K, respectively. The heat transfer to the gas during the isothermal expansion is 1200 kJ. At the end of the isothermal expansion the pressure is 800 kPa (State 3). After adiabatic expansion of the gas, the pressure decreases to 14.73 kPa (State 4). Consider variable specific heats for carbon dioxide.

(a) Determine the pressure (kPa) at the start and end of adiabatic compression.

(b) Find the volume (m3) of at the start and end of isothermal heat rejection.

(c) Calculate work (kJ) and heat transfer (kJ) for each process in the cycle.

(d) Calculate the thermal efficiency (%) of the cycle using work and heat transfer. Check that the value matches the Carnot efficiency.

(e) Show the cycle on P-V diagram.

Reference no: EM13629759

Questions Cloud

What is the magnitude of the acceleration of a proton : a total of 3.02 106 electrons are placed on an initially uncharged wire of length 1.45 m.a what is the magnitude of
The following table shows part of the probability : the following table shows part of the probability distribution for a random variable x.x fx0 0.21 ?2 0.153 ?4 0.15a.
A smoking lounge is to accommodate 15 heavy smokers the : a smoking lounge is to accommodate 15 heavy smokers. the minimum fresh air requirement for smoking lounges is specified
What is the velocity of the ball after it has moved : a small metal ball with a mass of 5.3 g and a charge of 6.3 mc is located at a distance of 0.70 m above the ground in
Determine the pressure kpa at the start and end of : six kilograms of carbon dioxide in a piston-cylinder device execute a carnot cycle consisting of the following four
An eight-cylinder car has two cylinders that are defective : an eight-cylinder car has two cylinders that are defective and need to be replaced. if the mechanic randomly selects
What is the direction of the force that you exert on the : a what is the direction of the force that you exert on the coin during the toss but before the coin leaves your hand?b
Super cola sales breakdown is 80 regular soda and 20 diet : super cola sales breakdown is 80 regular soda and 20 diet soda. of the regular soda 60 are purchased by men. of the
Nine coins are tossed let x be the number of coins that : a nine coins are tossed. let x be the number of coins that turn up heads. find px 4 and px 6.b a coin is tossed

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd