Determine the pressure in bars and the enthalpy in kjkg at

Assignment Help Mechanical Engineering
Reference no: EM13625044

A piston cylinder device having an initial volume of 2 m3 initially contains steam at 10 bars and 200oC (state 1). The contents are compressed isothermally until the volume is 41.95 percent of the initial volume (state 2). At this point the volume is held fixed and heat transfer occurs until a pressure of 40 bars is obtained (state 3).

a. Determine the pressure in bars and the enthalpy, in kJ/kg, at state 2.

b. Determine the temperature, in degrees Celsius, and the enthalpy at state 3.

c. Sketch the two processes on a Pv diagram with respect to the vapor dome.

Reference no: EM13625044

Questions Cloud

An evacuated 150 l tank is connected to a line flowing air : an evacuated 150 l tank is connected to a line flowing air at room temperature 25 degrees c and 8 mpa pressure. the
If the motorcycle travels over the crest at half speed : a motorcycle is traveling up one side of the hill and down the other side. the crest of the hill is a circular arc with
A centrifuge is used to remove solids from a 140 ppg mud : a centrifuge is used to remove solids from a 14.0 ppg mud using 8.33 ppg water. the mud and water enter the centrifuge
A pair of dice is rolled 270 times using the normal curve : a pair of dice is rolled 270 times. using the normal curve approximation what is the probability that a total of 7
Determine the pressure in bars and the enthalpy in kjkg at : a piston cylinder device having an initial volume of 2 m3 initially contains steam at 10 bars and 200oc state 1. the
A long bar of rectangular cross section 04 m x 06 m on a : a long bar of rectangular cross section 0.4 m x 0.6 m on a side and having a thermal conductivity of 1.5 wm x k is
When a 45 n force is applied tangentially to the disk : a solid cylindrical disk has a radius of 0.25 m and it can rotate about a vertical axis.a. when a 45 n force is applied
The inside temperature of the firebrick layer was measured : calculate the rate of heat loss through the vertical walls of a boiler furnace 4m by 3m by 3m high.the walls are
The motion of the electron can be seen as a circular : if we have an electron orbiting an atomic nucleus. we may think the electron is doing a circular motion around the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  How much money must be deposited to the fund

Principles of Engineering Economic Analysis-Time value of money-use of gradient factor is expected

  Determine the phase or phases in a system

Determine the phase or phases in a system consisting of H2O at the following conditions and sketch p-v and T-v diagrams shown the locations of each state?

  An insulated piston-cylinder device contains 2l of

an insulated piston-cylinder device contains 2l of saturated liquid water at a pressure of 150kpa-which is constant

  What input voltage will be computed by the adc

A successive approximation ADC has 4 bits and a reference voltage of 10 V. If the input voltage is 2.8 V, describe each step the ADC undergoes to determine the value of the 4 bits. What input voltage will be computed by the ADC?

  Determine the critical crack length for an internal crack

determine the critical crack length for an internal crack in a thick 2024-t6 alloy plate that has a racture toughness

  Determine the maximum speed

A vehicle of mass 1500kg and track 1.8m has a centre of mass located centrally at 1,1m above the ground. It has to travel around a bend of 56m radius to the centre of mass.

  The isentropic efficiency of the nozzle is 94 determine the

water enters an insulated nozzle operating under steady conditions at a pressure of 60 psia a temperature of 350 degf

  Consider a cross flow of water saturated water that comes

consider a cross flow of water saturated water that comes at 20c with a velocity of 5 ms on the surface of a

  Determine the reading on the pressure gage in psig when all

a transparent rigid container is filled with 2 gallons of water. initially the pressure is measured to be 10.2 psig

  An electric moter drivers an axial fan assuming that the

an electric moter drivers an axial fan assuming that the desired air velocity 65degree f existing the fan is 50mph and

  Derive an expression for the temperature distribution in

a bonding operation utilizes a laser to provide a constant heat flux q0 across the top surface of a thin

  Determine a the quality of steam in the tank at the initial

a rigid tank contains 7.5 kg of saturated water mixture at 400 kpa. a valve at the bottom of the tank is now opened and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd