Determine the pressure drop across the value

Assignment Help Mechanical Engineering
Reference no: EM13827519

Question-

In the following figure, ethylbenzene flows at 1000 gpm and 445°F. The frictional pressure drop between point 1 and 2 is 13psi.

(a) Please recommend a proper location for the control valve

(b) Please calculate the pressure drop across the control valve.

234_figure.jpg

Additional information-

The question relates to Mechanical Engineering and the question is about determine the right place for the control valve from the above given diagram and to determine the pressure drop across the value where ethylbenzene flows at 1000 gpm and 445°F. The solution contains the calculations in detailed.

Reference no: EM13827519

Questions Cloud

Case study analysis nuview contact lens coloring : Case Study Analysis Nuview Contact Lens Coloring
Difference in the number of african american and white women : The problem about Sociology and the problem explains about the difference in the number of African American and white women being diagnosed of breast cancer and the number of deaths occurring.
Calculate the flow rate in gpm of a hydrocarbon stream : Calculate the flow rate in gpm of a hydrocarbon stream (specific gravity equal to 0.65) though a 3-inch equal percentage valve that is 40% open based on stem position for the Cv given in Table 1 and the installed pressure drop in table 2
Write about gulf airlines with some of the marketing issues : Write about Gulf Airlines with some of the marketing issues
Determine the pressure drop across the value : The question relates to Mechanical Engineering and the question is about determine the right place for the control valve from the above given diagram and to determine the pressure drop across the value where ethylbenzene flows at 1000 gpm and 445°..
Product service experience and transformation analysis : Product Service Experience and Transformation Analysis
Allocate resources efficiently : Prepare Microsoft Word document that addresses the situations and meets APA standards - One of his advisors insists that this would not work, another advisor thinks it's good policy. Which advisor is correct?
What is the control objective of this process : Grains, such as com and sorghum are used to produce ethanol for use in motor oil. A process for producing ethanol from grains is shown in the following figure. What is the control objective of this process
Which term do you prefer health disparities or inequality : The problem is from Sociology and the problem explore the use of the words disparities, inequality, inequity, etc and the significance of their differences.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd