User Account

All Pages

Determine the pressure between the sleeve and cylinder when

Assignment Help Civil Engineering
Reference no: EM13535612

A cylinder 4 in. internal diameter and 1 in. thick, has an external sleeve 1 in. thick shrunk on it. The shrinkage is such that, when the internal fluid pressure (fluid in the cylinder) is applied, maximum shear stress both in the tube and sleeve is 16000 psi. Calculate the fluid pressure, and determine the pressure between the sleeve and cylinder when the fluid pressure is absent.

Reference no: EM13535612

Questions Cloud

Include a sketch of each cross-section drawn to scale : Problem Statement: A singly reinforced rectangular beam is to be designed, with effective depth approximately 1.5 times the width, to carry a service live load of 2000 lb/ft in addition to its own weight, on a 24 ft simple span. The ACI Code load fac..
Design the shear reinforcement : Problem Statement: A rectangular beam having b = 10 in. and d = 17.5 in. spans 15 ft face to face of simple supports. It is reinforced for flexure with three
Identify the contaminants on site and explain : Identify the contaminants on site and explain their hazards in relation to the proposed design and its construction. Describe the ‘In-situ’ and Ex-situ’ treatments that could be used and their relative merits
Briefly outline with the use of neat labelled sketches : It is proposed to make a new pedestrian access running directly south from University Square to Silvertown. The physical barriers that need to be overcome are the Royal Docks and the City Airport runway.
Determine the pressure between the sleeve and cylinder when : Maximum shear stress both in the tube and sleeve is 16000 psi. Calculate the fluid pressure, and determine the pressure between the sleeve and cylinder when the fluid pressure is absent.
What is normally consolidated clay : Compute the nominal shear strength of an M10 x 7.5 of A 572 grade 65 steel
Compute the probable settlement of the building : The construction of a multi storied building started in January 1989 & was completed in June 1990. The total consolidation settlement of the building was estimated to be 8 cm.
Determine the quantify the losses in this system : At Point A, in a pipeline carrying water (γ=62.4 lb/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2ps
What is the average crack spacing for that reinforcement : Compute the effective composite modulus of subgrade reaction (please consider the subbase, the presence of a relatively shallow rock foundation, and the potential loss of support)

Reviews

Write a Review

Civil Engineering Questions & Answers

  Give the phase and the missing property of

Give the phase and the missing property of P, T, v and x. Put the values in a table withcolumns P, T, v, and x.

  Write a c program for that writes the value to memory

Write a C program for a HCS12 microcontroller that writes the value, 0x78, to Memory Location VAR1 and then calls a delay function. The delay function should generate a delay of 0.25 milliseconds.

  Calculate the angle a between the vectors a and c

If A cross product B = the vector C, calculate the angle "a" between the vectors A and C and between the angle "b" between the vectors B and C.

  Describe what design speed was used for the curve

Lane widths are 12ft and the superelevation is .006 and was set assuming maximum fs. If the necessary sight distance required 52ft of lateral clearance from the roadway center line, what design speed was used for the curve

  Over what distance does discharge increase in depth occur

In a short section of a channel carrying a steady discharge of 36 m^3/s, the depth is seen to increase from 1.6 m to 1.75 m. The channel is rectangular, 20 m wide with a bedslope of 0.0002 and Manning n of 0.014.

  Will the quality of the coarse aggregate increase

To adjust the mix so as to increase the compressive strength, the water-to-cement ratio is reduced to 0.45. Will the quality of the coarse aggregate increase, decrease, or stay the same

  Determine the resultant of the four force sand its line of

Four forces act on a small airplane in flight: its weight (24kN), the thrust provided by the engine (10 kN), the lift providedby the wings (23 kN), and the drag resulting from its motionthrough the air (3 kN).

  Find the maximum cargo weight that the barge can carry

Assume you are responsible for determining the maximum load that can be carried by a rectangular barge that is 8 m wide and 18 m long. The water line when the barge is empty is 3 m below the level of the cargo deck.

  Estimate the minimum number of tugs needed to tow

Simplify the shape of the base and the 4 legs and estimate the minimum number of tugs needed to tow the structure at the required speed. The most powerful tugs can produce a thrust of approximately 2000kN,i.e.200tons.

  In the non-inertial cs fixed at the top of the vertical

the linkage shown below is made up of two 3-kg rectangular members 0.4 m by 0.1 m and is flying through the air. at the

  What is the ratio of the strain energy u1 in the tube

a thin walled circular tube and a solid circular bar of the same material are subjected to torsion. the tube and the bar have the same cross-sectional area and the same length.

  How to approximate the number of the 120 intervals

At a specified point on a highway, vehicles are known to arrive according to a poisson process. Vehicles are counted in 20 second intervals, and vehicle counts are taken in 120 of these time intervals.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd