Determine the power required to drive the compressor

Assignment Help Civil Engineering
Reference no: EM131233945

A certain industrial process requires a steady 0.5 kg/s supply of compressed air at 500 kPa at a maximum temperature of 30?C. This air is to be supplied by installing a compressor and an after cooler; see Fig. P7.47. Local ambient conditions are 100 kPa, 20?C. Using an isentropic compressor efficiency of 80%, determine the power required to drive the compressor and the rate of heat rejection in the after cooler.

879_b560fda6-7740-481f-8d52-97fabde9f2ab.png

Reference no: EM131233945

Questions Cloud

What is attribution as it pertains to copyright : Briefly describe the purpose and benefits of the Creative Commons. Briefly describe how Creative Commons help creators opt-out of copyright altogether?
Management department at scholars university holds workshops : Management department at Scholars University holds workshops annually in collaboration with two other universities. The department wishes to create a database with the following entities and attributes:
How much interest do you earn on a deposit : If the bank states an effective interest rate of 12% per annum, and there are 52.15 weeks, how much interest do you earn on a deposit of $100,000 over 1 week?
Monmouth county reclamation center : John Stanton and Harv Straus owned Global Recycling Solutions, LLC, which was acquired through an asset purchase agreement by Greenstar New Jersey, LLC, in July 2008. The acquisition included the Monmouth County Reclamation Center (“MCRC”).
Determine the power required to drive the compressor : Local ambient conditions are 100 kPa, 20?C. Using an isentropic compressor efficiency of 80%, determine the power required to drive the compressor and the rate of heat rejection in the after cooler.
New generation of management wants : Masbet Corporation has been a family owned company. While they are celebrating their 50th Anniversary the new generation of management wants to make some changes in the way communication flows.
When is it appropriate to apply the z-test for proportions : When is it appropriate to apply the z-test as the inferential technique and why? When is it appropriate to apply the t-test as the inferential technique and why? When is it appropriate to apply the z-test for proportions?
What are some of the current trends organizations face : What are some of the current trends organizations face with mobile computing security and what are some of the remediation steps companies take to ensure data confidentiality and integrity?
How much interest do you earn on a deposit : If the bank quotes interest of 12% per annum, and there are 52.15 weeks,-  how much interest do you earn on a deposit of $100,000 over 1 year?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Rate of change in volume

A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.

  Find solution of bvp and equation which defines critical l

A uniform thin column of length L, positioned vertically with one end embedded in the ground, will deflect, or bend away,from the vertical under the influence of its own weight

  What is the maximum length to which it may be stretched

what is the maximum load that may be applied to a specimen with a cross sectional area of 130 mm^2 without plastic deformation.

  What pressure gradient along a streamline

What pressure gradient along a streamline, dp/ds, is required to accelerate water upwards in a pipe at 0.5 m/s^2 ? The incline is 1:10, i.e., 1 m upward for every 10 m horizontal.

  Find the error probability for each bit

Find the error probability (in terms of the Q function) for each bit in each of the two systems

  Identify the contaminants on site and explain

Identify the contaminants on site and explain their hazards in relation to the proposed design and its construction. Describe the ‘In-situ’ and Ex-situ’ treatments that could be used and their relative merits

  Determine the size of pipe for a water temperature

The difference in water level is 60ft. Determine the size of pipe for a water temperature of 60 degrees Fahrenheit. Apply The Darcy-Weisbach equation.

  Estimate the maximum outlet velocity that this system could

A mining engineer plans to do hydraulic mining with a high-speedjet of water. a lake is located H=300 m above the mine site Waterwill be delivered through L=900 m of hte fire house with an inside diameter D

  Find the final temperature and the work done by the air

The system comes to equilibrium. Find the final temperature and the work done by the air in the process and plot the process P-V diagram.

  Projectile shot vertically upward

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  How sustainability and green engineering can be integrated

Discussion on how sustainability and green engineering can be integrated in the four components of materials science and engineering?

  Determine the magnitude of reaction

Determine the magnitude of reaction at point A (in kips) of a 20' beam with 5kips at 4' of the beam and 2kips at 9' of the beam at 350lbs./ft.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd