Determine the power needed to drive the pump if the pump

Assignment Help Mechanical Engineering
Reference no: EM13612636

A feed water pump operates with a flow rate of 350 kg/s. The water enters at 420 K. The inlet pressure is 0.7 MPa and the outlet pressure 20 MPa. Determine the power needed to drive the pump if the pump isentropic efficiency is 87%. Also determine the outlet temperature of the water. Plot the process on T-s coordinates. Show the saturated liquid line. Compressed liquid properties for water are given below. Note: Isentropic efficiency is defined differently for pumps and for turbines.

Pressure

(MPa)

Temperature

(K)

Specific volume

(m3/kg)

Enthalpy

(kJ/kg)

Entropy

(kJ/kg·K)

0.7 0.7 0.7

20 20 20

400 410 420

422.02 422.73 430

0.0010664 0.0010763 0.0010869

0.0010768 0.0010775 0.0010852

533.26 575.91 618.77

639.57 642.67 673.60

1.6008 1.7061 1.8094

1.8094 1.8166 1.8891

Reference no: EM13612636

Questions Cloud

A university with a high water bill is interested in : a university with a high water bill is interested in estimating the mean amount of time that students spend in the
A sanitation department is interested in estimating the : a sanitation department is interested in estimating the mean amount of garbage per bin for all bins in the city. in a
A drug company is studying two drugs a and b which are used : a drug company is studying two drugs a and b which are used to dilate the pupils of human eyes during examination. nine
A random variable x has the following probability : a random variable x has the following probability distrubution.x fx0 0.081 0.172 0.453 0.254 0.05a. deterime the
Determine the power needed to drive the pump if the pump : a feed water pump operates with a flow rate of 350 kgs. the water enters at 420 k. the inlet pressure is 0.7 mpa and
Estimate the mean and standard deviation of this process : components used in a cellular telephone are manufactured with nominal dimension of .3 mm and lower and upper
You are visiting las vegas and would like to come home with : you are visiting las vegas and would like to come home with more money than you arrived with. use your knowledge of
Determine the absolute pressure of the water at the ground : the water level in a sealed tank is 26 m above the ground. the pressure in the air space above the water is 0.25 mpa
The gap between the two plates is h 0005 m the fluid has a : there is flow between two plates as shown in the schematic. the bottom plate is stationary. the top plate is moving at

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd