Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A balacnced, three-phase, delta-connected load is supplied by a balanced, three-phase, wye-connected source over a balanced three-phase line. the source voltages are in abc phase sequence in which Van is 19.94<0 KV and the line impedance is 10+j80Ohm per phase. if the balanced load consists of three equal impedances of 60+j30ohm, determine the following:
(a)the line currents Ia, Ib and Ic.
(b)the pahse voltages Vab+, Vbc+, Vca+of the load.
(c)the phase currents Iab,Ibc and Ica of the load.
Design a first-order RC high-pass filter for the given cut-off frequency of fC = 2400 Hz and the capacitor value of C = 47 nF. What is the required resistor value
The maximum ratings for all resistors of this type are 250 (V) and ½ (W). What range of resistance values are limited by the maximum voltage rating of 250 (V), and what range of resistance values are limited by the maximum power of ½ (W)
The transfer function of a circuit is given by H(s)=2 s+4/4s^2+2s+2 a. Express the transfer function in a form in which the coefficients of the highest power of s are unity in both numerator and denominator. b. What is the characteristic equation o..
The voltage across the load must remain between 4.7 and 5.0 V for all values of load current. Come up with (draw) a voltage-divider network to supply the load. You may assume that resistors of any value desired are available.
A 3.3V, 30 A dc power supply is to be designed with a ripple of less than 2.5%. Assume that a half-wave rectifier circuit (60 Hz) with a capacitor filter is used.
the worker's safety harness D-ring is attached to a 12-foot shock absorbing lanyard that is securely fastened to the structure at a point 40 feet above ground level. Does this arrangement violate OSHA standards for fall protection? Explain.
Assume that in addition to the sine-wave signal you have a dc reference voltage of 1.5 V available. Sketch the output signal waveform.
Solve the equation z^2+z+1=0 using z=(x,y) and the basic definitions. (Hint: Note that y does not equal 0 because the equation X^2+X+1 does not equal 0 for any real number x.)
A mote draws an average of 200mA when "awake", 0.1mA when "sleeping", and 400mA (total) when "transmitting". Transmitting data takes 2ms, and sensor acquisition takes 1ms. If the maximum size battery available is 5000mAh
A plane circular disk of radius 0.25m rotates at a speed of 200 rad/s about an axis through the center of the disk perpendicular to the plane of the disk. There is a uniform magnetic flux B = 1 Tesla parallel to the axis of rotation.
Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the following motor control specifications:1) A motor must be started and stopped from any one of three start/stop pushbotton stations.
Design a BCD-to-7-segment decoder/driver (code converter) by using two different VHDLs (two projects - one low elvel and one high level) You need to turn in vhdl codes, testbench codes, simulation waveforms
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd