Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Test reveal that a normal driver takes about 0.75s before he can react to a situation to avoid a collision. It takes about 3 seconds for a drunk driver to do the same. If such drivers are traveling on a straight road at 44ft/s and their cars can decelerate at 2ft/s^2, determine the shortest stopping distance for each from the moment they see the pedestrians.
2.A pipe network in the form of a cube is made with twelve identical pipes. Each pipe forms an edge of the cube. If the entire inflow and outflow occurs at two adjacent corners, determine the percentage of the flow which passes through the pipe connecting these two corners.
A rectangular beam with a width of a 8 in. an effective depth of 10 in., and a total depth of 12 in., is reinforced with a single fiberglass reinforcing bar that has a cross sectional area of 0.45 in^2
You are designing a new thermometer using Galinstan, an alloy of gallium, indium, and tin that is a liquid at normal living temperatures. The coefficcient of thermal expansion is 190*10^-6 (1/kelvin)
a three-span continuous h20 timber beam with three equal spans of 1.3 mts supports a uniform load of 22.46 knm2nbspwith
Problem: A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D+S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.
The height of the instrument during this measurement was 1.60m From the same setup from point A, the zenith angle and slope distance toward point B are measured as 83deg 32'30" and 186.23m respectively, while the elevation of point B is 315.34m AM..
A 32-in.-wide by 0.125-in.-thick by 110-in.-long steel sheet is to be formed into a hollow section by being bent through 360° and having the long edges welded (i.e., butt-welded) together. Assume a cross-sectional medial length of 32 in.
Water with a static pressure of 1.96kN/M2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M2. Determine the velocity (V)
The following data were collected at a nest of piezometers (several piezometers of different depths located within a few feet of each other), each of which is screened (open) only at the bottom.
During an engine test on the ground, a propeller thrust T = 4000 N is generated on the 1500 kg airplane with mass center at G. The main wheels at B are locked and do not skid; the small tail wheel at A has no brake.
A tire carries a 5,000-lb load and has a pressure of 100 psi. The pavement has a modulus of elasticity of 43,500 psi. A deflection of 0.016 inches is observed at a point on the pavement surface 0.8 inches away from the tire load.
A Charpy V Notch test was conducted for an ASTM A572 Grade 50 bridge steel. the average values of the test results at four different test temperatires were found to be
The truck is driving onto the stationary barge at the speed of v1. The masses of the truck and the barge are m and M, respectively. The barge is free to move on the water and the water resistance is to be ignored.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd