User Account

All Pages

Determine the percent increase in the rate

Assignment Help Electrical Engineering
Reference no: EM13880763

The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick. There are to be 100 fins per meter. The convective heat transfer coefficient, both for the wall and the fins, is estimated at 35 W/(m2 K). With this information, determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.

GIVEN

Aluminum fins with a rectangular cross section
Dimensions: 2.5 cm long and 0.25 mm thick
Number of fins per meter = 100
The convective heat transfer coefficient ( hc ) = 35 W/(m2 K)

ASSUMPTIONS

Steady state heat transfer

1993_determine the percent increase in the rate.jpg

Reference no: EM13880763

Questions Cloud

What is the after tax cash flow from the sale of this asset : Consider an asset that costs $600,000 and is depreciated straight-line to zero over its eight-year tax life. The asset is to be used in a five-year project; at the end of the project, the asset can be sold for $170,000. If the relevant tax rate is 35..
What is opec optimal level of production : Suppose that, over the short run (say, the next five years), demand for OPEC oil is given by Q = 57.5 - .5P or, equivalently, P = 115 - 2Q. (Here Q is measured in millions of barrels per day.) OPEC's marginal cost per barrel is $15- What is OPE..
What are the appropriate abc groups of inventory items : What are the appropriate ABC groups of inventory items? If demand for an item is 3 units per day, and delivery lead-time is 15 days, what should we use for a simple re-order point?
What is the present value of this cash flow pattern : You have been offered the opportunity to invest in a project that will pay $5958 per year at the end of years one through three and $10986 per year at the end of years four and five. If the appropriate discount rate is 7.11 percent per year, what is ..
Determine the percent increase in the rate : The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick.
Manufacturing plant and equipment to actually produce stamps : Consider a project to supply 118 million postage stamps per year to the U.S. Postal Service for the next five years. You have an idle parcel of land available that cost $2,080,000 five years ago;You will need to install $5.58 million in new manufactu..
Compute the firm total profit : To maximize profit, how much foam insulation should firm S plan to produce and sell? What price should it charge?
Create portfolio with expected return : You have $260,000 to invest in a stock portfolio. Your choices are Stock H, with an expected return of 14 percent, and Stock L, with an expected return of 11.1 percent. If your goal is to create a portfolio with an expected return of 12.5 percent, ho..
Effect of the insulation thickness on the temperature : Explore the effect of the insulation thickness on the temperature of the aluminum and the heat loss per unit tube length

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is maximum load that can be connected to tansformer

Three single phase transformers rated at 100kVA, 13.2kV / 2.4kV are connected in wye -delta on a 3 phase, 18kV line. What is the maximum load that can be connected to the transformer bank

  Find the rms value ot the ac component

a generic rectifier is supplied from a 115v 60hz ac source and operates with a firing angel of 30 degrees. For the output voltage of the rectifier find: The dc component The rms value othe ac component

  Explain scada system

Explain the function of the HMI in a SCADA system.

  Design values of w-l of the set and clock nmos transistors

A CMOS clocked SR flip-flop uses a technology with unCox = 100 uA/V^2, upCox = 25 uA/V^2, VDD = 2.5V, Vtn = -Vtp = 0.5V and the total capacitance at the output nodes equals 15fF. The inverter threshold voltage VM = 2.5V.

  Operational amplifier circuit to design an active

Use a capacitor, a resistor and an operational amplifier circuit to design an active first order low pass filter which passes frequencies that human can hear (below 15kHz). Show all the calculations required to find the values of all the passive c..

  Find frequency response and impulse response or rc network

Consider an RC network that have an input x(t) and an output y(t) that is taken from the terminals of the capacitor C. a.Draw the circuit; showall the necessary symbols on the drawing. b.Find the frequency response H(jw) and the impulse response h(t)..

  How you could transmit two independent base-band information

Explain how you could transmit two independent base-band information signals by using SSB on a common carrier frequency.

  What is the current in the line feeding the three loads

Two machines and a lighting load are connected in parallel to a 240 V(rms), 60 Hz line. The first machine uses 230 kW of power at 0.85 power factor lagging. The second machine uses 95 kVA at 0.882 power factor leading. The lightening load consumes..

  Determine the sampling rate if it is chosen to be greater

The highest frequency contained in a certain analog signal is 4 kHz. Determine the sampling rate if it is chosen to be 50% greater than the theoretical minimum.

  Design a single-pole pin diode switch operating at f

Design a single-pole PIN diode switch operating at f = 8 GHz. A PINdiode has the following parameters: Cj = 0.03 pF, R(forward) = 0.2Ω, R(reverse) = 7 Ω, Li = 0.6 nH, Zo = 50 Ω. Find what type of connection, series or shunt, gives thegreatest ratio..

  Draw logic diagram of four-bit register with four flip flop

Draw the logic diagram of a four-bit register with four D flip-flops and four 4 X 1 multiplexers with mode selection inputs s1 and s0. The register operates according to he following function table

  Write the ybus matrix

Identify the bus types and the unknown variables of the power flow problem. Write the complete set of equations needed to solve the load flow problem.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd