Determine the percent error n in replacing the sine and the

Assignment Help Civil Engineering
Reference no: EM13564984

1.Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results

2.Maintenance expenses for a bridge in Georgia are estimated to be $200,000 for the first eight years followed by two separate million dollar expenditures in years 12 and 18. The expected life of the bridge is thirty years. For i=6% what is the present worth of maintaining the bridge?

Reference no: EM13564984

Questions Cloud

How much heat had to be transferred to the vessel : Alkaloids are chemical compounds containing nitrogen that can be produced by plant cells. In an experiment, an insulated closed vessel 1.673 m3 in volume was injected with a dilute water solution containing two alkaloids: ajmalicine and serpentine.
Calculate the axial strain and the transverse strain in the : A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel
What is the stress along the top edge and the bottom edge : A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis. what is the stress along the top edge and the bottom edge caus..
What is the maximum column load in kips that could be placed : What is the maximum column load in kips that could be placed on a 4-ft square temporary footing on a sand for which the standard resistance is about N=15 and the water table is at the surface? A factor of safety of 2 is to be maintained against beari..
Determine the percent error n in replacing the sine and the : Determine the percent error n in replacing the sine and the tangent of an angle by the value of the angle in radians for angle values 5 degrees, 10 degrees, and 20 degrees. Explain the qualitative difference between the sine and tangent results
Determine the design esal if the design life is 20 year : A six-lane divided highway is to be designed to replace an existing highway. The present AADT (both directions) of 6000 vehicles is expected to grow at 5% per year. Assume SN = 4 and pt = 2.5
Calculate the extreme-fibre stresses at mid-span : Calculate the extreme-fibre stresses at mid-span for a simply supported prestressed concrete beam with a depth of 750mm, width 370mm and span of 7m under working live load of 65 kN/m and self-weight. The prestressing force.
Calculate the maximum pressure developed when a 10 in. thick : Calculate the maximum pressure developed when a 10 in. thick wall 10 ft high is to be poured at the rate of 3ft/hr at a temperature of 70 degrees F.
What is the steady state co concentration : What is the steady state CO concentration? c. Given the steady state CO mixing ratio in part above (assume 1 atmosphere pressure and 288 K) what is the resulting %COHb and what is the health impact if exposed to this concentration overnight while you..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the flow rate that can be delivered

A water line to a home is usually 3⁄4" copper tube. What is the flow rate that can be delivered and still maintain laminar flow in the tube?

  Determine the dimensions of the best hydraulic trapezoidal

Determine the dimensions of the best hydraulic trapezoidal concrete channel section to convey water at a rate of 2200 gal per min on a channel slope of 0.015 m/m.

  You have been hired to design a horizontal curve

You have been hired to design a horizontalcurve with a 40 degree central angle ( delta= 40) for a two-laneroad with 10 ft lanes. If the design speed is 70 mph, emax=6%

  Determine the net power delivered to the generator

Air enters the compressor at 98 kPa and 295 K at a rate of 10 kg/s and exits at 1 MPa and 620 K. Determine the net power delivered to the generator by the turbine.

  How to select the pit from which the soil should be bought

The void ratio of the compacted fill is specified as 0.7. Four borrow pits are available along with each of the respective void ratios along with the cost per cubic meter for moving the soil to the proposed construction site.

  Estimate the boundary layer thickness at the end of train

The flow over the train is similar to flow over a flat plate. Estimate the boundary layer thickness at the end of the train, which is 125 m long. The temperature is 10°C.

  What minimum salvage value would be required for technology

A new chemical remediation tank is needed. Current technology tanks, which costs $150,000, MUST BE DRAINED AND TREATED EVERY TWO YEARS AT A COST OF $30,000; THE TANKS WILL LAST TEN YEARS, AND EACH WILL HAVE A SALVAGE VALUE OF 5%. OF FIRST COST.

  How many exploratory borings will be required and to what

A one-story, 50-m wide X 90-m long manufacturing building is to be built on a site underlain by medium dense to dense silty sand with occasional gravel

  A pre-engineering base line was run down a very steep

a pre-engineering base line was run down a very steep hill.rather than measure horizontaily down hill with steel tape

  What is the maximum external pull in each of the 4 gears

If a tractor with 23-hp, a max speed of 3.6 mph in 1st gear and an effieiciency of 92% is operated operated down a 4% slope and the rolling resistance is 80 lb/ton, what is the maximum external pull in each of the 4 gears.

  Ompare the ratio of kinetic energy to the potential energy

If a unit mass of groundwater accelerates from rest to an average linear velocity of 1 m per year and climbs a vertical distance of 1 m, compare the ratio of kinetic energy to the potential energy of the unit of groundwater.

  Determine percentage of truck as seen by stationary observer

From a photograph one observs that on a level section of highway 20% of the vehicles are trucks, 80% are cars, and that there are 50 vehicles per mile of highway. The trucks travel at 40 mph, the cars at 50 mph.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd