Determine the overall transfer function of the block diagram

Assignment Help Chemical Engineering
Reference no: EM131154062

It is desired to control the exit concentration of c3 of the liquid blending system shown in Figure Q3. Using the information given below, do the following:

a. Develop the dynamic model for this system as functions of time for any given variation in inputs.

b. Perform a degrees of freedom analysis. Identify all input and output variables.

c. Draw a block diagram for the composition control scheme. (Use the symbols in the figure as much as possible.)

d. Derive an expression for each transfer function

e. Determine the overall transfer function of the block diagram.

Available information:

1. The tank is perfectly mixed.

2. The volumetric flow rate and solute concentration of stream 2, q2 and c2, vary with time, while those of stream 1 are constant.

3. The flow-head relation for the valve on the exit line is given by;

4. The densities of all three streams are identical and do not vary with time.

Reference no: EM131154062

Questions Cloud

What is macro-expansion : What is macro-expansion? List the key notions concerning macro expansion. Write an algorithm to outline the macro-expansion using macro-expansion counter.
What is an operating system : What is an operating system? List the typical functions of operating systems.
Classify disasters based on the way : How can you classify disasters based on the way they emerge and become an issue for an organization?
Management team and operations : Describe who will be the CEO and his/her qualifications/experiences in the product/service industry, including both education and work and other relevant experiences.
Determine the overall transfer function of the block diagram : Develop the dynamic model for this system as functions of time for any given variation in inputs.
Draw the state diagram of a process : Draw the state diagram of a process from its creation to termination, including all transitions, and briefly elaborate every state and every transition.
Compare job design approaches and employee job performance : Compare and contrast job design approaches and their relevance to an employee’s job performance. Identify and discuss the five core job characteristics in the Job Characteristics Model, and describe the three strategies for improving employee motivat..
Why did iceland recover so quickly from the financial crisis : Read the Making the Connection short case titled Why Did Iceland Recover So Quickly from the Financial Crisis? Then post your posting this week beginning to discuss what you've read and watched in the video.
Conditional critical regions : Give a solution for readers-writers problem using conditional critical regions.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Catalytic dehydrogenation of ethyl benzene

Styrene can be made by catalytic dehydrogenation of ethyl benzene. The reaction is usually carried out in the presence of steam, which acts as a heat carrier and reduces coking on the catalyst.

  Isolating a heat exchanger

Select suitable valve types for the following applications: a. Isolating a heat exchanger. b. Manual control of the water flow into a tank used for making up batches of sodium hydroxide solution.

  Develop a series of design graphs

Develop a series of design graphs that can be used to demonstrate acceptable combinations of tubes dimensions

  Should the second analysis be discarded

Should the second analysis be discarded based on a 0.95 probability level?

  Prepare the design and evaluation of a new chemical

prepare the design and evaluation of a new chemical manufacturing process.1 acetylation reactor2 separation of

  Calculate the induced armature voltage at rated load

A 50-kW, 250-V, short-shunt compound generator has the following data: Ra = 0.06 Ω, RS = 0.04 Ω, and Rf = 125 Ω. Calculate the induced armature voltage at rated load and terminal voltage. Take 2 V as the total brush-contact drop.

  Find the value of the induced emf

(Note: The number of parallel paths is equal to the number of poles for lap windings, while it is equal to 2 for wave windings.)

  Calculate the instantaneous and rms values of the voltage

Calculate the instantaneous and rms values of the voltage induced in a 150-turn coil on the armature, if the axial length of the armature and its inner diameter are both 100 mm.

  Draw the logic diagram of the enabled d latch

Draw the logic diagram of the enabled D latch using only NAND gates.

  Determine the final state if cooling is at constant volume

Wet steam at 200 °C with 80% moisture is heated by removing 600 kJ/kg of heat. Determine the final state (pressure and temperature and quality, if a two-phase system) if cooling is at constant pressure.

  Calculate the final temperature

Consider a diatomic gas, N2, at 298 K. This gas is compressed reversibly and adiabatically from 15 dm3 to 5.0 dm3. Assume that the heat capacity of this gas is CV=5R/2, and that it behaves ideally. Calculate the final temperature, T2, of the gas.

  Calculate the heat that must be supplied to the system

n-Octane is compressed reversibly at constant temperature along the critical isotherm until the critical point is reached. The initial pressure is 1 bar. The pressure takes place in a closed system. Use the Lee-Kesler method to calculate what is t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd