Determine the overall mass transfer coefficient for gas

Assignment Help Mechanical Engineering
Reference no: EM131243489

Assignment - Mass Transfer and Absorptions

Q1. Water is used to absorb the vapor of methanol at 300 K and 101.325 kPa. The concentration of methanol in both gas and liquid phases are very low, with the equilibrium relation following Henry's Law. The known parameters are:

solubility of methanol in water = 1.995 kmol/(m3.kPa)

local mass transfer coefficient for gas film kG = 1.55E-5 kmol/(m2.s.kPa)

local mass transfer coefficient for liquid film kL = 2.08E-5kmol/(m2.s.kmol/m3)

(1) Please determine the overall mass transfer coefficient for gas phase, KG.

(2) And determine the percentage of mass transfer resistance in gas film out of the overall resistance.

(3) At steady operation in certain section of the absorption column, the partial pressure of methanol is 5 kPa and the liquid composition is 2.11 kmol/m3. Please determine the methanol absorption rate NA, [kmol/(m2.h)].

Q2. Water is used to absorb NH3 (mole fraction 0.1) from air at 1 atm in a counter current operation. The gas mixture at 313 K is fed to the bottom of the column at a flow rate of 0.556 m3/s and a velocity of 1.2 m/s. Water is introduced to the column from the top. Due to the enthalpy of dissolution, the temperature of the ammonium water is higher at the bottom of the column. The temperature and composition distribution in the liquid phase from top to bottom of the column, with corresponding gas phase equilibrium compositions are described by Table 1.

Table 1.

temperature of NH3 solution

composition of NH3 solution

gas phase composition

deg C

X, kmol (NH3) / kmol (H2O)

Y*, kmol (NH3) / kmol (air)

20

0

0

23.5

0.005

0.0056

26

0.01

0.01

29

0.015

0.018

31.5

0.02

0.027

34

0.025

0.04

36.5

0.03

0.054

39.5

0.035

0.074

42

0.04

0.097

44.5

0.045

0.125

47

0.05

0.156

(1) If the recovery of NH3 is 95%, assuming air is totally inert, please determine the theoretical minimum liquid flow rate Lmin, (kg/s)

(2) If the real liquid flow rate is 1.1 times of the theoretical minimum, and if the KGa is known to be 0.0556 kmol/(m3.s), please determine the diameter of the column, (m). 

(3) Please determine the height of the packings (m), based on the above information.

Q3. Clean water is used to remove SO2 from air through a counter current scrubbing process to reach a 95% recovery, in which the flow rate of gas is 5000 std m3/h containing 10%(v/v) SO2. The equilibrium for the solute between gas and liquid is Y* = 26.7 X.

(1) Please determine the required liquid flow rate, assuming 1.5 fold of the theoretical minimum, (kmol/h).

(2) Please determine the number of theoretical plate.

(3) Using the number of plate determined from (2), if the recovery is to be increased from 95% to 98%, what will be the new water consumption (kmol/h)?

Reference no: EM131243489

Questions Cloud

What kind of job are you most interested in : What kind of job are you most interested in? What were your most important achievements in your last position? What is your greatest strength? Why do you think you can do this job better than anyone else?
Statement represent consumer surplus : Does this statement represent consumer surplus, producer surplus, or neither? "Even though I was willing to pay up to $135 for a used laptop, I bought a used laptop for only $126."
What will be the steady-state temperature of the sphere : A sphere of 30-mm diameter whose surface is diffuse and gray with an emissivity of 0.8 is placed in a large oven whose walls are of uniform temperature at 600 K.
Calculate the equivalent interest rate : For simple interest of 5% for ten years, calculate the equivalent interest rate with (i) annual, (ii) quarterly and (iii) continuous compounding. Assume 30/360 daycount.
Determine the overall mass transfer coefficient for gas : ENSC3019 Assignment - Mass Transfer and Absorptions. Water is used to absorb the vapor of methanol at 300 K and 101.325 kPa. Please determine the overall mass transfer coefficient for gas phase, KG. And determine the percentage of mass transfer resis..
Hich of two coatings would result in a lower roof temperture : Which of the two coatings would result in a lower roof temperature? Which is preferred for summer use? For winter use? Sketch the spectral distribution of αλ that would be ideal for summer use. For winter use.
Deduce which rate has larger standard deviation : Derive an expression for yAM in terms of ySB. You can assume all years have 365 days. - Deduce which rate has larger standard deviation.
What will the velocity of the moon be afterwards : A 1-kg flower pot resting on a balcony 25 m above the ground. The railing gives way and it falls to the ground. If it is going 20 m/s when it hits the ground, how much heat did it create by friction on its way down?
What is the drying rate per unit length of the oven : Blackbody behavior may be assumed for the water surface and for the oven wall.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd