User Account

All Pages

Determine the number of cycles per minute

Assignment Help Mechanical Engineering
Reference no: EM13688986

Each cycle, the working fluid of a sterling engine receives 2.67 kJ of energy in the form of heat in the combustion chamber. The engine operates with a thermal efficiency of 0.20 and delivers 4 kW of shaft power.
(a) Determine the number of cycles per minute
(b) Find the energy rejected as heat to the low temperature reservoir (atmosphere) per
cycle

Reference no: EM13688986

Questions Cloud

A manufacturing process at regular intervals : Samples of ?? 4 items each are taken from a manufacturing process at regular intervals.
How many rotations does the wheel make before coming to rest : The flywheel of a steam engine runs with a constant angular speed of 116 rev/min. How many rotations does the wheel make before coming to rest
A finite dt is a source of irreversibility : Q1) Heat transfer across a finite ΔT is a source of irreversibility. Why is this? Give 2 examples of other sources of irreversibility.
What is the electric field in this region : The electric potential at x = 3.0 m is 120 V, and the electric potential at x = 5.0 m is 190 V.  What is the electric field in this region
Determine the number of cycles per minute : Determine the number of cycles per minute
The tower is held in place by three cables : The tower is held in place by three cables. If the force of each cable acting on the tower is shown, determine the magnitude and coordinate direction angles of the resultant force. Take x = 20 m, y = 15 m
What is the magnitude of the current : A circular coil of radius 5.0 cm and resistance 0.20 ohm is placed in a uniform magnetic field perpendicular to the plane of the coil. What is the magnitude of the current in mA induced in the coil at the time t = 2.0 s
What should be the radius of curvature : A prescription for a corrective lens calls for +2.50 diopters. The lens maker grinds the lens from a "blank" with n = 1.60 and a convex front surface of radius of curvature of 19.0 cm. What should be the radius of curvature
What is the distance of this point from the axis : A tank holds a 1.44-m thick layer of oil that floats on a 0.96-m thick layer of brine. What is the distance of this point from the axis

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a the exit velocity of the nitrogen and b the

nitrogen gas at 60 kpa and 7degc enters an adiabatic diffuser steadily with a velocity of 275 mls and leaves at 85 kpa

  Water at 200kpa with a quality of 90 enters a well

water at 200kpa with a quality of 90 enters a well insulated compressor. it leaves this compressor at 1 mpa 300 celcius

  Determine the total time for the sled to reach the bottom

a sled is at the top of a snowhill that has a vertical height of 150 ft and slopes down with an angle of 20 degrees. if

  This power cycle produces wcycle1000 w determine the heat

a reversible power cycle operates at steady state between a thermal reservoir at 400 c and another one at 200 c. this

  How much pressure is required for a force output of 62275

1. how much pressure is required for a force output of 62275 newtons if the effective piston area of the cylinder is

  Determine the following a the gas pressure lbfin2 when the

a gas is contained in a vertical piston-cylinder arrangement. the 50-lbm piston initially rests on the bottom stops.

  The channel is rectangular 20 m wide with a bedslope of

a in a short section of a channel carrying a steady discharge of 36 m3s the depth is seen to increase from 1.6 m to

  The engine is shut down when the boats velocity has

a boat is subject to hydrodynamic drag forces of f 40v2n where v is the magnitude of velocity in ms. the boats mass is

  The vessel volume is 15m3 and a standard six-blade open

an agitation system is to be designed for a fluid having a density of 950kgm3 and viscosity of 0.005pas. the vessel

  Compute the force required to punch out a rectangular

Calculate the force required to punch out a rectangular hole 100m x 50mm in a 2mm thick aluminium sheet. The ultimate strength in shear is 125 MN/m^2.

  A spring-mass system is found to vibrate with a frequency

a spring-mass system is found to vibrate with a frequency of 120 cycles per minute in air and 100 cycles per minute in

  What is the maximum pressure this unit can withstand

a power unit has a power rating of 30 kw and supplies flow at a rate of 60 lpm, what is the maximum pressure this unit can withstand?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd