Determine the ntu values for each sampling port depth

Assignment Help Civil Engineering
Reference no: EM13297516

A pilot study was conducted to strip TCE at a concentration of 230 ppb from a contaminated groundwater using a small packed tower air stripper containing 50-mm diameter polytethylene intalox saddles. The packed tower was 30 cm in diameter with sampling ports located at packing depths of 0,2,4,6,8,10, and 12 meters. The loading of water to the tower was 0.039 m^3/(m^2/s), and the temperature of groundwater was 10 degrees celcius. The table below shows measure TCE concentrations in the water for several of the sampling ports:

Depth (m) TCE conc. (ppb) NTU
0 230
2 100
4 55
6 25
8 16

a) Determine the NTU values for each sampling port depth.
b) What was the overall mass transfer coefficient (Kla,s^-1) for TCE under the conditions studied in the pilot-scale test?
c) From the pilot-scale study, what packing depth in the tower would have been needed to obtain a concentration of 5 ppb TCE in the groundwater?

Reference no: EM13297516

Questions Cloud

What is the ph of solution of oxalic acid h2c2o4 : What is the pH of a 0.17 M solution of oxalic acid, H2C2O4. The Ka1,2 values of oxalic acid are 5.6 x 10-2 and 5.4 x 10-5.
Calculate the required plate area and the number of plates : An Electrostatic Precipitator must treat 500,000 acfm with 99% efficiency. Assuming an effective drift velocity of 0.4 ft/sec, calculate the required plate area in ft^2, and the number of plates if each is 20 ft tall by 10 ft long, and there are 4..
Explain how many grams of sodium formate and nacho2 : How many grams of sodium formate, NaCHO2, would have to be dissolved in 1.1 L of 0.20 M formic acid (pKa 3.74) to make the solution a buffer for pH 3.82
Calculate the inductance of the coil : A coil of wire is connected to an ideal 12.0-V battery at t = 0. At t = 14.2 ms, the current in the coil is 210 mA. calculate the inductance of the coil
Determine the ntu values for each sampling port depth : The packed tower was 30 cm in diameter with sampling ports located at packing depths of 0,2,4,6,8,10, and 12 meters. The loading of water to the tower was 0.039 m^3/(m^2/s), and the temperature of groundwater was 10 degrees celcius.
Explain substances to produce the indicated solution : Calculate the amount of water (in grams) that must be added to each of the following substances to produce the indicated solution 8.10g of urea(NH2)2CO in the preparation of 21.8 percent by mass solution 30.4g MgCl2 in the preparation of a 4.8 per..
Determine what is the volume needed along the road : A roadway is to be designed on a level terrain. The roadway is 500 ft. Six Cross Sections have been selected at 0 ft, 100 ft, 200 ft, 300 ft, 400 ft, and 500 ft. . The cross sections have areas of 130 ft2, 140 ft2, 70 ft2, 110 ft2, 80 ft2, and 25 ..
How fast is she going when she reaches the bottom : A novice skier starting from rest slides down a frictionless 32 degree incline whose vertical height is 125 meters
Determine the number of moles of water : Find the number of moles of water that can be formed if you have 158 mol of hydrogen gas and 74 mol of oxygen gas. Express your answer with the appropriate units.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculating coefficient of permeability

The temperature was 200C, and the void ratio (e) of the soil was 0.43. Calculate the "Coefficient of Permeability" in "centimeters per second" (Given, k = (QL)÷(A Δh t)).

  Difference between total and static pressure

The difference between the total and static pressure before a shock is 75 psi. What is the maximum static pressure that can exist at this point ahead of the shock? The gas is oxygen.

  Determine max torque that can be carried by hollow section

A 32-in.-wide by 0.125-in.-thick by 110-in.-long steel sheet is to be formed into a hollow section by being bent through 360° and having the long edges welded (i.e., butt-welded) together. Assume a cross-sectional medial length of 32 in.

  Conductive heat loss through the furnace wall

Assuming unit surface area, find the conductive heat loss through the furnace wall and the temperature at the interface of the fire clay and red brick.

  Determining stress fort rigid bar of negligible weight

The rigid bar of negligible weight is supported as shown. Find the stress in each rod if the temperature rises DeltaT after a load P is applied. Use the following data: area of steal rod 320mm2, bronze rod 1300mm2, thermal expansion coefficient Al..

  What is the original estimated duration of the project

The initial schedule called for 500 feet of pipeline to be installed each week, with the total construction cost projected to be $25 million. After 8 weeks, 4750' of pipeline has been installed at a cost of $11.25 million.

  Determine the cod

Determine the COD, carbonaceous BOD, and nitrogenous oxygen demand of a 100 mg/L solution of urea (N2H4CO)

  Calculate the depreciated portion of the ownership cost

Property taxes,insurance and storage will run 5%.What is the owning cost for the dozer?Use the time value method to calculate the depreciated portion of the ownership cost.

  Maximum volume of treated wastewater

Roughly what is the maximum Volume of treated wastewater should you put in the bottle if you want to have at least 2.0mg/l of DO at the test (filling the rest of the bottle with the water

  Design a horizontal curve with a 40-degree central angle

Design a horizontal curve with a 40-degree central angle (delta=40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06ft/ft. Give radius, degree of curvature, and length of curve.

  What will be the approximate amount of the quarterly payment

What annual investment is required at 8% per year compounded annually to accumulate to $100,000 at the end of 20 years?

  Determine what is the balance delay for the solution

A proposal has been submitted to replace a group of assembly workers, each working individually, with an assembly line. The following table gives the individual work elements. The demand rate for this job is 1600 units/week (assume 40h/week)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd