Determine the normal stresses induced in the steel and in

Assignment Help Mechanical Engineering
Reference no: EM13635316

Concrete post Ec=3.6x10^6 psi and alpha c = 5.5x10^-6 deg F is reinforced with 6 steel bars, each of 7/8 in diameter. Es=29x10^6 psi and alpha s =6.5x10^-6 deg F. Determine the normal stresses induced in the steel and in the concrete by a temperature rise of 65 deg f. Dimensions are 10in wide x 10in long and height of 6ft.

Reference no: EM13635316

Questions Cloud

As an example find the maximum acceleration of a beam that : a vibrating structural beam in a spacecraft can cause problems if the frequency of vibration is fairly high. even if
At an altitude of 19350 feet atop mount kilimanjaro in : at an altitude of 19350 feet atop mount kilimanjaro in kenya the boiling point of water is 81 degrees celsius.
Determine the smallest allowable dimensions a and b of the : 2 blocks of rubber with a modulus of rigidity g12 mpa are bonded to rigid supports and to a plate ab. knowing the
Two particles of charges q1 and q2 are separated by : two particles of charges q1 and q2 are separated by distance d. the net electric field due to the particles is zero at
Determine the normal stresses induced in the steel and in : concrete post ec3.6x106 psi and alpha c 5.5x10-6 deg f is reinforced with 6 steel bars each of 78 in diameter.
Calculate the difference in slope of the chemicalpotential : calculate the difference in slope of the chemicalpotential against temperature on either side ofa the normalfreezing
A particle with a mass of 20times10-5 and a charge of 23 is : a particle with a mass of 2.0times10-5 and a charge of 2.3 is released in a parallel plate uniform horizontal electric
Knowing the es29x106 psi and ec 36x106 psi determine the : a 4ft concrete post is reinforced with four steel bars each with a 34in diameter. knowing the es29x106 psi and ec
Based on the electronic configuration of the iron species : the bonding in ferrocene involves sharing of the 6 electrons from each cyclopentadienyl ring with the iron atom. based

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the volume of the tank in m3 and the final

five kilograms of water are contained in a closed rigid tank at an initial pressure of 20 bar and a quality of 50. heat

  Calculate the rate of heat transfer through the plates what

suppose that two plates thickness t0.027 m and area a1.2 m2 for each plate are mated together. the thermal conductivity

  A rankine steam power plant should operate with a high

a rankine steam power plant should operate with a high pressure of 3 mpa a low pressure of 10 kpa and the boiler exit

  One kmol of ideal gas cp30 jmolk is contained in a piston

one kmol of ideal gas cp30 jmolk is contained in a piston cylinder initially at 25c and 10bar. the mass of the piston

  What is the force p to keep the system in equilibrium

What is the force P to keep the system in equilibrium for the angles specified?

  A solid cylinder has a mass of 5kg a diameter of 9cm and is

a solid cylinder has a mass of 5kg a diameter of 9cm and is 60cm high. it starts at point a and must be moving at 2ms

  A bike rider has a frontal area of 04 m2 and a drag

a bike rider has a frontal area of 0.4 m2 and a drag coefficient cd of 0.9. if he is pedaling at 80 rpm. what average

  Sketch the cycle on a t-s diagram with respect to

water is the working fluid in an ideal vapor power cycle with reheat. superheated vapor enters the first turbine stage

  The angle f1 makes with the positive c axis is 30degrees

two forces f1 and f2 with magnitudes 40 and 55 newtons respectively act on an object at the origin. the angle f1 makes

  Assuming cold air standard assumptions for a spark ignition

assuming cold air standard assumptions for a spark ignition engine cycle otto and given the following data compression

  Between the inlet and an axial location of 2 feet the air

air flows in a round pipe at a rate of 0.015 lbmsec. the air enters the pipe at a temperature 76.8 of and a pressure

  The water will be cooled to 20 degrees c by passing it

50 degree c water is flowing in a 10mm diameter smooth tube. the mass flow rate of the water is 0.08 kgs. the water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd