Determine the normal capacity of the highway

Assignment Help Civil Engineering
Reference no: EM13563781

The capacity of a highway is suddenly reduced to 60 percent of its normal capacity due to closure of certain lanes in a work zone. The flow upstream of the work zone is 80 percent of the normal capacity of the highway. The Greenshields model describes the linear relationship between speed and density on the highway, the jam density of the highway is 112 vpm, and the mean free speed is 64.5 mph.

a. Determine the normal capacity of the highway, the capacity of the highway upstream of the work zone, and the capacity within or in the vicinity of the work zone.

b. Determine by what percentage the space mean speed at the vicinity of the work zone will be reduced compared to what it is upstream of the work zone.

c. Determine by what percentage the density at the vicinity of the work zone will be increased compared to what it is upstream of the work zone.

Reference no: EM13563781

Questions Cloud

Compute the force fa on the roller and the x- and y-componen : Three point loads 10,000, 7500 and 9000 kN act in line 5m apart near the surface of a soil mass. Calculate the vertical stress at a depth of 4m vertically below the centre (7500kN) load.
What is the minimum required temperture of the boiler : A coal fired steam power plant is to be designed for the purpose of generating electrical power for a city with a population of 60,000 residents. Based on an order-of-magnitude analysis
What is the total delay per cycle and delay per vehicle for : A left-turn movement has a maximum arrival rate of 200 veh/h. The saturation flow of this movement is 1400 veh/h. For this approach, the yellow time is 4 seconds, all red time is 2 seconds and total lost time is 3 seconds.
Determine the period and frequency of the motion : A 75-lb block is supported by the spring arrangement shown. The block is moved vertically downward from its equilibrium position and released. Knowing that the amplitude of the resulting motion is 2 in.,
Determine the normal capacity of the highway : Determine the normal capacity of the highway, the capacity of the highway upstream of the work zone, and the capacity within or in the vicinity of the work zone.
Find the minimum speed at which the train could pass over : Steam locomotives require water at such rates that the storage tank behind the locomotive was refilled at 100 mile interverals. one technique used was to place a long tank between the rails and the water the water would be scooped up as the locomotiv..
Determine the longest wait of any vehicle : An incident occurs on a freeway that has a capacity in the northbound direction, before the incident, of 4000 veh/h and a constant flow of 2900 veh/h during the morning commute.
What will be the approximate temperature of the alloy : Is it possible to have a copper-silver alloy of composition 50 wt% Ag-50 wt% Cu that at equilibrium, consists of α and β phases having mass fractions Wα = 0.60 and Wβ=0.40? If so what will be the approximate temperature of the alloy? If such an a..
How much heat has been transferred to the gas : A cylinder with a moveable piston holds .20 lb of hydrogen initially in a volume of 1 cu ft at a tem-perature of 1300 F. Then the volume is expanded to 2.5 cu ft while the gas pressure remains constant.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the change in diameter under load answer in mm

A cylinder of rock with a Poisson's ratio of 0.422 has ano-load length equal to 17.6 cm and a no-load diameter of 6.20cm. Under an axial compressive load the axial strain is foundto be -3.44 mm/m.

  Find area of steel reinforcement required for concrete tbeam

Find the area of steel reinforcement required for a concrete T-beam for the following data; f'c = 3 ksi, fy=50 ksi,d=28 in, t= 6 in., bw= 16 in., bf= 60 in., and the section sustains a factored bending moment of Mu=360 kip ft

  Detemine the elevation and stationing of the low point

A horizontal curve on a single lane highway has its pc at station 124+10 and its pi at station 131+40.the curve has a super elevation of 0.06 and its designed for 70 mi/hr.what is the station of the pt" is pending

  Explain the problem encountered in this measurement

A tensiometer is used to measure a compacted soil in the field that has a matric suction of 200 kPa under atmospheric conditions. The pore-water pressure measurement in the tensiometer reaches

  Find what must be the rated horsepower of the motor

What would be the resistance on a level road. What horsepower must be delivered to the wheels on the grade? If the efficiency is 80%, what must be the rated horsepower of the motor.

  What are two or three quality management tools used in data

what are two or three quality management tools used in data collection? what types of quality management tools do you

  A fan is to be selected to ventilate a bathroom whose

A fan is to be selected to ventilate a bathroom whose dimensions are 2 m x 3 m x 3 m. The air velocity is not to exceed 8 m/s to minimize vibration and noise.

  Determine current supplied if final temperature is 70 degree

Now 300 kJ of heat is transferred to the refrigerant at constant pressure while 110-V source supplies current to a resistor within the cylinder for 6 min. Determine the current supplied if the final temperature is 70 degrees C.

  Determine the type of water surface profile for depths

A 2.45 m wide rectangular channel has a bed slope of 0.0004 and Manning's roughness coefficient n of 0.015. For a discharge of 2.83 m^3/s, determine the type of water surface profile for depths of 1.52 m, 0.61 m, 0.30 m.

  Determine the theoretical discharge

A vertical triangular orifice in the wall of a reservoir has a base 0.9m long,0.6m below its vertex and 1.2 m below the water surface. determine the theoretical discharge?

  Calculate the carbon content required at surface of steel

A 0.02wt% C steel is to be carburized at 1200°C in 4 hrs with a point 0.6mm beneath the surface reaching 0.45wt%C. calculate the carbon content required at the surface of the steel.

  Determine constant angular acceleration the time required

When the gear rotates 18 revolutions, it achieves an angular velocity of omega= 40 rad/s , starting from rest. Determine its constant angular acceleration the time required.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd