Determine the moment of inertia of the cone

Assignment Help Civil Engineering
Reference no: EM13866207

Problem: Determine the moment of inertia of the cone with respect to a vertical y axis that passes through the cone's center of mass. What is the moment of inertia about a parallel axis y' that passes through the diameter of the base of the cone? The cone has a mass m.

1458_moment of inertia.jpg

Reference no: EM13866207

Questions Cloud

How you look back on that leadership experience : Discuss leadership experiences, what you learned from them, factors that influenced how you led, and how you look back on that leadership experience
Have cultural considerations influenced your choice : What strategies and/or tactics could Matt choose to use in negotiating with Red Star Holdings? Have cultural considerations influenced your choice and are there other alternatives available to Matt that can help him succeed in launching Cosmo Cloth..
The company uses a fifo cost flow assumption : On January 2, 2010, the Whistler Company purchased land for $450,000, from which it is estimated that 400,000 tons of ore could be extracted.
What does a computer know about a declared array? : What does a computer know about a declared array?
Determine the moment of inertia of the cone : Determine the moment of inertia of the cone with respect to a vertical y axis that passes through the cone's center of mass. What is the moment of inertia about a parallel axis y' that passes through the diameter of the base of the cone? The cone ..
Explain how a hold used promotional : Explain how A hold used promotional allowances to manipulate earnings. Refer to the fraud triangle described in this chapter and analyze the incentives pressures and opportunities to commit fraud at A hold
Cost per equivalent unit of production for conversion : Andrews Corporation uses a process costing system for manufacturing. The following information is available for the February in its Polishing Department: Equivalent units of production—direct materials 110,000 EUP Equivalent units of production—conve..
Carbon fossil fuels are utilized to power our vehicles : Carbon fossil fuels are utilized to power our vehicles, make oil, and even t-shirts. The EPA has determined that a car transforms a gallon of octane (C8H18) to 33.7 kWh (kilowatt*hours, an expression of energy) in order to power a vehicle.
The company also purchased some temporary housing : On July 1, 2010, the Amplex Company purchased a coal mine for $2 million. The estimated capacity of the mine was 800,000 tons. During 2010, the company mines 10,000 tons of coal per month and sells 9,000 tons per month.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the location on the wheel where the net

A wheel rolls to the right with an angular velocity of 2 rad/s while slowing down at a rate of 3 rad/s^2.. knowing the wheel rolls without sliding and ignoring the effect of gravity

  How much natural gas is needed to incinerate the gas stream

The preheaded waste gas stream of 4,000 ACFM is entering a thermal oxidizer. The waste gas stream temperature is 1000 F. How much natural gas is needed to incinerate this gas stream at a temperature of 1500F

  Determine the required shaker frequency to cause resonance

A floor slab has a fundamental bending frequency of 10Hz. A shaker is placed at the centre of the slab for a dynamic testing. The tests confirm that the slab displays a damping ratio of 2% of critical.

  How long would lake take to reduce h2s concentration form

Lake silbersee is located in the German city of Nuernberg. The lak's water quality has been diminishedbecause of high hydrogen sulfide concentrations that originate froma nearby leaking landfill.

  Determine the maximum bending stress that will occur

Determine the maximum bending stress that will occur in a timber beam of rectangular section 250mm x 80mm when a bending movement of 500N is applied about the x-x axis

  Find the required minimum area for the heat transfer neglect

Saturated liquid water at 1000 kPa flows at 2 kg/s inside a 10 cm outer diameter steel pipe and outside of the pipe is a flow of hot gases at 1000 K with a convection coefficient of h = 150 W/m2 K

  What are alternative treatment option for the removal of edc

What are alternative treatment options for the removal of EDCs in tertiary treatment? Be sure to justify any alternative treatment method you propose.

  Plot the variation of vertical stress with depth below centr

For a horizontal curve, the tangent length is 400 feet and the curve length is 789.59 feet the station of the PT=106+89.58, what is the station of PI?

  Find how long would the pipe have to be in feet to achieve

The flow in the river is 30ft^3/min and the first-order rate constant for disinfection is 6min^-1. 1)What kind of hydrodynamic model should you use. 2) write the mass balance equation for microorganisms in symbols at steady state. define symbols.

  How to select the lightest available w33 section

the 30 ft simple beam shown has lateral support spacing at 15 ft for its compression flange and consists of 50 ksi steel. the beam supports a gravity service dead load of 1.2 klf (includes beam weight) and a gravity live load of 3.4 klf

  A college student borrows 1500 during his senior year the

1.a college student borrows 1500 during his senior year. the loan is to be repaid in 20 equal quarterly installments.

  Write a user defined function named simplecharacter

Write a User Defined Function named SimpleCharacter that takes the character inputs either "Coffee" or "Tea" and returns the outputs High Octane for an input of "Coffee" and Low Octane for an input of "Tea".

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd