Determine the minimum required wire diameter

Assignment Help Mechanical Engineering
Reference no: EM13217872

A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi) for the steel.

Reference no: EM13217872

Questions Cloud

Explain which often causes the students to fall behind : Many students who take online classes do not realize that the time commitment for online classes is often more demanding than that for face-to-face classes, which often causes the students to fall behind when they take classes online.
Generation of relevant hypothesis : Development of problem statements and generation of relevant hypothesis and defining of the research objective
Calculate the power required to drive the plant : A refrigerating plant operating between temprature limit of 253k and 307k provides 4.5kJ/s of refrigerating effect. If the refrigerating efficiency of the plant is 0.76. calculate the power required to drive the plant.
What is the proeutectoid phase : Consider 1.0 kg of austenite containing 1.15 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).
Determine the minimum required wire diameter : A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2 and a yield strength of 860 MPa (12..
Determine the angle of twist of the end b : determine the angle of twist of the end B of the solid section relative to end C. The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The solid section has a diameter of 40 mm.
How to find sources inappropriate for an academic essay : Your audience is people currently studying for a degree in this field. You have a choice as to your writing goal. You can choose to either focus on explaining why this skill, quality or behavior is valuable to their success in the field or you can..
Compute the magnitude of the load : on the basis of the information given ,is it possiple to compute the magnitude of the load that is necessary to produce this change in length?
How many quarts of each should she use : Angela needs 20 quarts of 50% antifreeze solution in her radiator. She plans to obtain this by mixing some pure antifreeze with an appropriate amount of a 40% antifreeze solution. How many quarts of each should she use?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Future value your rich godfather has offered

Your rich godfather has offered you a choice of one of the three following alternatives: $10,000 now; $2,000 a year for eight yeaers; or $24,000 at the end of eight years

  Determine the largest load p

A knowing that the normal stress magnitude in each link is not to exceed 24 ksi, the shearing stress in pin F is not to exceed 15 ksi, and the deflection of point A is not to exceed .08 in.

  Design problem - piston and flywheel

Design Problem - Piston and Flywheel : Analyze the motion of the crankshaft AB and flywheel for 0 ≤ θ ≤ 4Π (two complete rotations of the crankshaft, or all four cycles, beginning and ending at TDC), for different values of the four design paramete..

  Measuring fracture toughness

Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness and Describe the fracture behaviour of the insulation tape loaded with a small crack. Explain w..

  Explain midrange and amplitude components

Midrange and amplitude components, A shaft is subjected to a completely reversed bending stress such that Xmax=40kpsi and Xmin=-40kpsi

  What are the uses of wind tunnels including

this is concerned a little more into aerodynamics, what are the uses of wind tunnels including the importance of geometric and dynamic similarity and wind tunnel interference?

  What can be said about the expected defect rate

Given that the nominal diameter (per print) is 15.00mm +/-0.10mm, what can be said about the expected defect rate?

  Turbomachinery - impulse and reaction turbines

Question about Turbomachinery - Impulse & Reaction Turbines, An impulse air turbine rotor with a blade speed (U) of 300 m/s is measured to have a relative rotor inlet velocity (W_1) of 750 m/s at an angle of 69 degrees and an outlet relative veloc..

  Determine the speed of the collar

the 2-kg collar is released from rest at A and travels along the smooth vertical guide. determine the speed of the collar when it reaches position B.Also ,find the normal force exerted on the collar at this position.the spring has an unstrectched ..

  Define a jack-screw has a handle inches long

A jack-screw has a handle 35 inches long and a pitch of 7/32 inches. If a pull of 15 lbs. is required at the end of the handle to lift a 3,000 lbs.

  Find the magnitude of the average velocity

Remember that velocity is a vector quantity so find the magnitude of the average velocity and the angle of average velocity from the horizon

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd