Determine the minimum pipe diameters required to restrict

Assignment Help Mechanical Engineering
Reference no: EM13626946

Consider a steam turbine in which steam enters at 10.45 MPa and 780K with a flow rate of 38.739 kg/s. A portion of the steam is extracted from the turbine after partial expansion at three different locations. The extracted steam is then led to various heat exchangers. The mass flow rates and the temperatures and pressures at each extraction point are given.

1. mass flow=4.343 kg/s P=3.054 MPa T=620K

2. mass flow=4.345 kg/s P=0.332 MPa T=482K

3. mass flow=2.871 kg/s P=0.136 MPa x=0.949

The remaining wet steam exits the turbine at 11.5 kpa with a quality of 0.88. Determine the minimum pipe diameters required to restrict the maximum inlet velocity to 50 m/s, the maximum extraction velocities each to 75 m/s and the turbine oulet velocity to 130 m/s.

Reference no: EM13626946

Questions Cloud

The peak of the mountain while travelling horizontally with : a helicopter pilot drop supplies to a standard avalanche survivor located on the east side of the a mountain that
Suppose you are an art dealer you specialize in buying : suppose you are an art dealer. you specialize in buying paintings by unknown painters at auctions and re-selling them
An lc circuit consists of a capacitor with c290mf and an : an lc circuit consists of a capacitor with c2.90mf and an inductor with l 30.0mh. at t 0 the capacitor has a charge
Assume that salaries are normally distributed the standard : according to salary wizard the average base salary for a brand manager in houston texas is 88592 and the average base
Determine the minimum pipe diameters required to restrict : consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the
Assume that a signal passes through an opening of 423 m : in conventional television signals are broadcast from towers to home receivers. even when a receiver is not in direct
A truck traveling at vo 60mph when the driver applies the : a truck traveling at vo 60mph when the driver applies the brakes to come to stop the deceleration of the truck is
Consider a concentric circular-tube annulus with outer : consider a concentric circular-tube annulus with outer diameter 2.5cm and inner diameter 1.25cm in which air is flowing
If 002 kg leaks out and the temperature drops to 27oc find : carbon monoxide is initially in a 50 l tank at 210 kpa and 127c.a determine the mass of the gas in kilograms.b if 0.02

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd