Determine the minimum elevation difference across channel

Assignment Help Civil Engineering
Reference no: EM13318119

A 2 m diameter semicircular channel made of brickwork is to transport water to a distance of 1.7 km uniformly. If the flow rate is to reach 200 m3/min when the channel is full, determine the minimum elevation difference across the channel.

Reference no: EM13318119

Questions Cloud

Find the average power consumed by this circuit : A generator with an rms voltage of 15\30V is connected in series to a resistor 3.25 kilo-ohm and a capacitor 3.50 microfarad. Using the frequency found in part A, find the average power consumed by this circuit
At what rate must heat be supplied to the power plant : At a coal-burning power plant a steam turbine is operated with a power output of 548 MW. At what rate must heat be supplied to the power plant by burning coal
Explain the relevant facts and decision of the court : Identify if this is a civil or criminal dispute and explain the relevant facts and decision of the court - Identify which key pieces of legislation did the court examine in arriving at its decision. Further, outline the process by which legislation..
Find the power factor for an rc circuit : Find the power factor for an RC circuit connected to a 70.0Hz generator with an rms voltage of 155 V
Determine the minimum elevation difference across channel : A 2 m diameter semicircular channel made of brickwork is to transport water to a distance of 1.7 km uniformly. If the flow rate is to reach 200 m3/min when the channel is full, determine the minimum elevation difference across the channel.
What is the distance of the two particles : What is the distance of closest approach of the two particles? (Assume that the gold nucleus remains stationary
At what load would you expect the specimen to fracture : Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm.
Determine the angular velocity of the door : A 10 g bullet traveling at 440m/s strikes a 7.0kg , 1.2-m-wide door at the edge opposite the hinge. What is the angular velocity of the door just after impact
Find the area of the parallelogram with vertices : Find the area of the parallelogram with vertices: P(0,0,0), Q(-2,4,0), R(-2,2,-2), S(-4,6,-2).

Reviews

Write a Review

Civil Engineering Questions & Answers

  How fast will the car be traveling when it reaches the tree

a car is traveling at sea level at 78 mi/h on a 4% upgrade before the driver sees a fallen tree in the roadway 150 feet away. the coefficient of road adhesion is 0.8. The car weighs 2700 lbs, has a drag coefficiant of 0.35, a frontal area of 18 ft..

  What does flattened mean for engineering and for managers

Thomas Friedman's bestseller, The World is Flat, says that the world has been, in his words, "flattened" or leveled which increases accessibility and competition worldwide. What does this mean for engineering and for managers who deal with enginee..

  Calculate the minimum flow rate

Calculate the minimum flow rate (m^3/hr) of river water needed to acheive pre cooling hot, pasteurized liquid prodcut assuming that 10% heat is lost to the surroundings during exchange and that the water temp after cooling should not exceed 25 deg..

  Determine the angle that vo forms with vertical by rocket

If the rocket's decent parachute does not deploy and the rocket lands 340 ft from A, determine the angle (alpha) that vo forms with the vertical, the maximum height h reached by the rocket, and the duration of the flight.

  Find allowable load p that can be supported by connection

A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa.

  Determine the initial length of the rod measured

To determine the original length of a slender rod given the normal strain and deformation experienced by the rod due to an applied axial load. rod AB is subjected to the loading of two blocks, each of weight W

  Calculate the unit weight and dry unit weight of the soil

A cube of moist soil weighs 330 lb and has a volume of 3.00 ft3. Its moisture content is 27.0% and the specific gravity of solids is 2.72. Compute the void ratio, porosity, degree of saturation, unit weight and dry unit weight of this soil.

  How far will the column of mercury in the tube be depressed

An open clean glass tube, having a diameter of 3 mm is inserted vertically into a dish of mercury at 20c .How far will the column of mercury (S.G =13.6) in the tube be depressed in (mm) given the following information. Theta = 130 and surface tens..

  Help with a site plan

Help with a site plan - Design on paper to add some other things in it.

  Determine the final density of the gas-carbon dioxide

Carbon dioxide at 30 C and 320 kPa absolute pressure expands isothermally to an absolute pressure of 170 kPa. Determine the final density of the gas.

  How to sketch p-v diagram as the pressure is raised

The phase diagram of a typical simple substance contains three phases , liquid vapor and solid separated by boundaries . The critical point terminates the liquid-vapor transition, in water it is at Pc=220.9 bar and Tc=374 degres celcius

  Calculate consolidation settlement 3 years after placement

The investigation results indicated that the clay had a saturated density of 1.6 Mg/m3, an average initial void ratio of 1.8 and the preconsolidation pressure at the mid depth of the clay layer was 20 kPa.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd