Determine the minimum diameter shaft that can be used

Assignment Help Civil Engineering
Reference no: EM13543436

The electric motor at A exerts a torque of 800N.m on the steel shaft from A to D. This has a torque of -300N.m at B and -500N.m at C. the dimensions are

shaft(a-b)=0.4m

shaft(b-c)=0.6m

shaft(c-d)=0.3m

Design specificaions require that the diameter of the shaft be uniform from A to D and that the angle of twist between A to D not exceed 1.5 degrees.

Knowing that the masximum shear stress must not be greater than or equals to 60Mpa, and G= 77GPa, determine the minimum diameter shaft that can be used.

Reference no: EM13543436

Questions Cloud

Will such a procedure produce a greater flowrate : A 12in diameter water main in your city has become very rough due to rust and corrosion, it has been suggested that the flowrate through the this pipe can be increased by inserting a smooth plastic liner into the pipe.
How much time should each employee spend at each in order : To avoid boredom, employees are assigned all three tasks at different times during the shift. Each employee has to work at least half an hour at each station during a five hour shift. How much time should each employee spend at each in order to maxim..
Provide the velocity distribution for steady flow case : An infinite, long, solid, vertical cylinder of radius R is located in infinite mass of compressible liquid. Provide the velocity distribution for steady flow case
Determine the normal stress in each rod. show all work : Two steel rods with fixed supports at A and C are attached by a rigid flange at point B and a downward load of 120 kN is applied to the flange. The upper rod has a cross section of 800 mm^2 and the lower rod has
Determine the minimum diameter shaft that can be used : The electric motor at A exerts a torque of 800N.m on the steel shaft from A to D. This has a torque of -300N.m at B and -500N.m at C. the dimensions are
Why does a design engineer need to know the location of the : Course Ab of a five sided traverse runs due north. From the giben balanced interior angles to the right, compute and tabulate the bearings and azimuths from north for each side of the traverses.
What is the left turn adjustment factor for the case describ : An intersection approach has three lanes, permitted left turns, and 6% left-turning volume with a through vehicle equivalent of 5.0 tvu/left turn. The saturation flow rate for through vehicles under prevailing conditions is 1,700 veh/hg/ln.
Determine the vertical deflection at c : The bent road has an E=200 GPa, G=75 GPa, and a radius of 30 mm. Use Castigliano's theorem and determine the vertical deflection at C. Include the effects of bending, shear, and torsional strain energy.
Determine the power that must be supplied to the pump at : Crude oil flows through a level section of the Alaskan pipeline at a rate of 1.6 million barrels per day (1 barrels=42 US gallons) the pipe inside diameter is 48 inch and its roughness is equivalent to galvanized iron.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Engineering ethics and ethical issue

what is the engineering ethics course where to write about any engineering ethical case and discuss the ethical issue?

  Engineering ethics and concept and cases

what is the engineering ethics case related to civil engineering with reference and discuss all the engineering ethics issues which covered the "Engineering etics concepte and cases?

  Transportation and management

In the construction management, there is a lot of procurement route that are necessary and suitable for the construction industry.

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  Personalized Cancer Therapy-A step forward

Cancer is the uncontrolled growth of abnormal cells in the body resulting in tumours that can be benign or malignant (cancerous cells). A proper treatment is necessary to fight with this serious disease.

  Discuss the different environmental companies

Discuss the different agencies, institutes, centers, different environmental companies that are active in UAE.

  Develop a simple urban constructed wetland design

Develop a simple urban constructed wetland design.

  Evaluate company performance in relation to GRI standards

Evaluate company performance in relation to GRI standards and comment on Stigler's theory.

  Water system design

Determine the corresponding error in the computed discharge

  Hydraulic behaviour in open channel

Describe how test flumes and associated equipment are used to assess and confirm hydraulic behaviour in open channel

  Write a paper on steel sustainability

Write a paper on steel sustainability.

  Writing case study about bridge collapse

Writing case study about bridge collapse

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd