Determine the minimum cover of sand

Assignment Help Mechanical Engineering
Reference no: EM131242751

The tunnel of the previous problem is sunk into a trench that has been dredged in the river bottom, and then covered with sand. The volumetric weight of the sand is 20 kN/m3. Determine the minimum cover of sand necessary to prevent floatation of the tunnel.

565_c2e8abee-d568-46d1-af3a-e00ab920b2ae.png

Reference no: EM131242751

Questions Cloud

Calculate the draught : A tunnel of square cross section, 8 m × 8 m, has a weight (above water) of 50 ton per meter length. The tunnel is being floated to its destination, with its two ends closed by temporary sheets. Calculate the draught (the depth of the bottom below ..
How the recommended corporate policy is socially responsible : Assess how the recommended corporate policy is socially responsible. Support the recommended policy with well-reasoned analysis and specific examples.
Elements of internal and external environment : What elements of internal and external environment contributed to Facebook's success? Which elements of internal/external context create challenges for facebook?
Determine which is more applicable across range of situation : Write a one to two page paper in which you determine which is more applicable across the widest possible range of situations: process modeling or configuration management. Be sure to explain your rationale.
Determine the minimum cover of sand : The tunnel of the previous problem is sunk into a trench that has been dredged in the river bottom, and then covered with sand. The volumetric weight of the sand is 20 kN/m3. Determine the minimum cover of sand necessary to prevent floatation of th..
What did you learn about e-learning and training : What did you learn about E-Learning and training? Why would it be important to Understand as an HR director? What are some of the advantages of corporate universities?
What are the four spiritual laws of evangelism : What are the Four Spiritual Laws of Evangelism? - Writing a paper on Methods of Evangelism and trying to figure out where to start.
Explain how you would redefine homeland security readiness : What type of relationship do you think FEMA and the DHS should have in the future regarding the rebuilding of the nation's all-hazards emergency management system? That is, inclusionary, supervisory, equal partners, etc. Explain your answer.
Find the maximum gradient inside the sheet pile wall : Sketch a flow net for the situation shown in Figure 8.7, and calculate the total discharge. Compare the result with the estimate made at the end of that chapter.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd