Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Problem Assignment - Vertical Load Capacity of URM Walls
The unreinforced, double-wythe brick wall shown below is constructed of bricks with a flat-wise compressive strength of 6000 psi that are laid in Type S mortar (made with masonry cement). No prisms are tested. Cores in the bricks have an area less than 25% of the gross area of the units. Grout is placed between the wythes to bond the wall together so that it acts compositely.
1. For the unreinforced masonry wall shown below, determine the maximum load per foot per the 2016 TMS 402 requirements that can be applied at an eccentricity equal to:
(a) 0.00"
(b) 1.50"
(c) 3.00"
2. Determine the maximum vertical force per foot that can be applied to the wall if the tensile strength is assumed to be equal to zero. Assume that the maximum compressive stress is limited to the value set by the 2016 TMS 402 for allowable axial compressive stress.
The A-36 steel post is subjected to the forces shown. If the strain gauges a and b at point A give readings of ?a = 300(10-6 ) and ?b = 175(10-6 )
An electrodialysis is used to treat a stream of 125 m3/d produced water with a salinity of 13,000 mg/L NaCl before the produced water is discharged to the river with the flow rate of 5 million L/d and salinity of 20 mg/L NaCl
Determine the largest screw spacing for the pi-shaped beams that allows the beams to carry an ultimate shear load of V = 2000 lbs. Each screw can support 350 lbs.
Determine the water level rise in an unconfined aquifer produced by a seasonal precipitation of four inches. The aquifers porosity is 20 percent and its specific retention is 9 percent.
Suppose that the distance from the lake outlet to the withdrawal cannot be more than 20 mi. What should be the new volume of the lake?
A crest vertical curve and a horizontal curve on the same highway have the same design speed. The equal-tangent vertical curve connects a +3% initial grade with a +1% final grade and has a PVC at 101+78 and a PVT at 106+72
A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm.
A BOD test was conducted on the unchlorinated effluent of a municipal treatment plant. The wastewater portion added to a 300 mL BOD bottle was 8 ml. The dissolved oxygen values and incubation periods are listed below. Determine the 5-day BOD value..
calculate the: 1) molar concentration of metal ion in the stock coagulant solution; 2) coagulant feed rate (into the process water flow stream) in units of L/day and L/min; 3) alkalinity consumed (in the process water flow stream) in units of mg/L..
An aquifer is 45 meters deep and has a well that pumps water at 850 cubic meters per day. One observation well is located 45 meters away and has a water surface that is 44.35 meters above the bottom of the aquifer.
A horizontal true centrifugal casting process is used to make brass bushings with the following dimensions: length = 10 cm, outside diameter = 15 cm, and inside diameter = 12 cm.
What is the percent change in pressure that a scuba diver in salt water will feel going from 50 to 40m of depth? What is the percent change from 10m to the surface? Use absolute pressure and assume standard atmospheric conditions. Would the answer ch..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd