Determine the maximum value of the average

Assignment Help Civil Engineering
Reference no: EM13563852

1.In a given month, a watershed with an area of 1500 m^2 received 100 cm of precipitation. During the same month, the loss due to evaporation was 15cm. Ignore losses due to transpiration and infiltration due to ground water. What would be the average rate of flow measured in a gage at the outlet of the watershed in m^3/day?

2.the player kicks a football with an initial speed of 90 ft/s. determine the time the ball was in the air and the angle of the kick. the distance is 126ft

3.The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member BE, (b) in member CF.

Reference no: EM13563852

Questions Cloud

Determine the grade of the road : The natural water of a sample taken from a soil deposit was found to be 11.5%. it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1..
What total volume of this soil is required to obtain : A construction site requires 35,000 yds^3 of soil in a compacted state with a moist unit weight of 126 pcf at a water content of 14%. if the uncompacted soil currently has a unit weight of 96 pcf and water content of 14%
Determine the gravitational force acting between two spheres : Determine the gravitational force acting between two spheres that are touching each other. The mass of each sphere is 400 kg and the radius is 300mm.
Determine the evaporation rate for a reservoir if the wind : Determine the evaporation rate for a reservoir if the wind speed is 40 mph and the surface temperature is 15 degrees Celsius and the overlaying temperature is 25 degrees Celsius. and the relative humidity is 30 percent
Determine the maximum value of the average : The frame shown consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member..
Determine the maximum negative moment in each span : A three span continuos beam has spans of 27, 30, 27 feet, total unfactored dead loads are 2,600 pounds per linear foot, unfactored live loads are 2,000 pounds per linear foot. For load combination 1.2D + 1.6L
Plot the shear and moment diagrams for the beam : Given simply supported beam with an overhang. The beam is 12 inches wide by 24 inches deep, and the slab is 6 inches deep. use a roof live load of 20 psf, and a concrete density of 150 pdf
How much sand did he place in the drum : A truck driver used sand to soak up a 1 g spill of lindane (C6H6Cl6). He placed the contaminated soil in an open drum which then filled with 150 L of water during a rainstorm. You test the water and find a concentration of 17 M.
What is the generic soil cleanup criteria for direct contact : Based on Michigan law, (a) what is the generic soil cleanup criteria for direct contact with residential soils contaminated with lead? Report your answer in units of "ppm" (

Reviews

Write a Review

Civil Engineering Questions & Answers

  How reliable do you think this estimate is

It the mean annual runoff of a drainage basin of 10000 km^2 is 140 m^3/s, and the average annual precipitation is 105 cm, estimate the ET losses for the area in 1 year. What are your assumptions? How reliable do you think this estimate is?

  What is maximum acceleration from rest for car with engine

The car weights 2450 lb, the mechanical efficiency of the drivetrain is 90%, and the wheel radius is 14 inches. The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque.

  Define energy transfer in mechanical systems

Energy transfer in mechanical systems, A wheel is 800mm in diamiter and has a mass of 1000kg. on a horizontal surface without skidding, the vehicle accelerates uniformly at 0.5m/s^2 for 5 seconds.

  Determine what length of new pipe is needed

a buried horizontal concrete pipe (n=0.012) of unknown length needs to be replaces. the length is not known because the original plans for the pipeline route have been lost. the pressure head drop along the segment that needs to be replaced is 29...

  Compute the suitable equal tangent vertical curve

A 301 stainless steel wire is suspended vertically from itsend. The wire is 400 ft long, diameter .75 inches, specific weight= 489 lb/ cubic foot.

  What is the predicted number of zebra mussels years from now

The zebra mussels have a net growth rate of 0.09 yr-1. At the current time there are 176 zebra mussels in the stream. What is the predicted number of zebra mussels 5, 10, and 20 years from now

  Freeway capacity and los

A four-lane freeway (two lanes in each direction) is on mountainous terrain with 11ft lanes, a 5ft right-side shoulder, interchange spacing of one every 10 miles, and a 60mph base free-flow speed.

  Determine the flow discharge in the canal

A trapezoidal canal with a bottom width of 1.5m, a side slope Z=1, has a longitudinal slope of 0.4% and n=0.025. If the water depth in section 1 is 1.52 m and in section

  Compute semiannual coupon payment investor will receive

If, on 8/1/2019, 3-year municipal bonds with an AA- rating and a coupon rate of 6.50% (payable semiannually) are selling for $100.00, what would be the fair market value of the 300 Whittier bonds (not including the 8/1/2019 coupon payment)

  What is the effective stress 25 feet deep if the specific

What is the effective stress 25 feet deep if the specific weight of the dry soil (dry unit weight) is 120 pcf and the water table is 12 feet deep?

  What is the uniform flow in cfs when the pipe is half full

A concrete (n=0.013) stormwater channel, 6-feet in diameter, has a bed slope of 0.01%. What is the uniform flow in cfs when the pipe is half full

  What percentage of the water evaporates

Saturated liquid water at 1.0 MPa is throttled adiabatically to a pressure of 0.4 MPa. If the change is kinetic energy is negligible, what percentage of the water evaporates during this throttling process?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd