Determine the maximum value for i and the time

Assignment Help Electrical Engineering
Reference no: EM13263863

The source-free circuit depricted in Fig. 9.1 is constructed using a 10mH inductor, a 1mF capacitor, and a 1.5k ohms resistor.
a) Calculate alpha ( neperfrequency or exponential damping coefficient), omega-sub-delta (natural resonance frequency), and omega-sub-zero (resonant frequency).
b) Write the equation which describes the current i for t>0.
c) Determine the maximum value for i, and the time at which it occurs, if the inductor initially stores no energy and v(0-)=9V

Reference no: EM13263863

Questions Cloud

Determine the boolean function that multiplexer implements : An 8x1 multiplexer has inputs A, B, and C connected to the selection inputs S2, S1, and S0, respectively. The data inputs I0 through I7, are as follows: I1 = I2 = I7 = 0; I3 = I5 = 1; I0 = I4 = D; and I6 = D'. Determine the Boolean function that t..
Calculate the heat input to the gas : Consider the process AB is this TS diagram for 2 moles of SO3 with all degrees of freedom active. calculate the heat input to the gas
What will the cash flows for this project be : The firm has a tax rate of 35 percent, an opportunity cost of capital of 12 percent, and it expects net working capital to increase by $100,000 at the beginning of the project.
Design a combinational circuit that compares two numbers : Design a combinational circuit that compares two 4-bit numbers to check if they are equal. The circuit output is equal to 1 if the two numbers are equal and 0 otherwise.
Determine the maximum value for i and the time : The source-free circuit depricted in Fig. 9.1 is constructed using a 10mH inductor, a 1mF capacitor, and a 1.5k ohms resistor. a) Calculate alpha ( neperfrequency or exponential damping coefficient), omega-sub-delta (natural resonance frequency)
Find the mutual inductance of the two solenoids : A long solenoid of r =1cm and lnght l=1m is inserted into another long solenoid of radius r=3cm, Find the mutual inductance of the two solenoids
What is number of modes if waveguide with thickness is used : What is the largest thickness d of a planar symmetric dielectric waveguide with refractive indexes n_1=1.50 n_2=1.46 for which there is only on TE mode at lambda_0=1.3 micrometers. What is the number of modes if a waveguide with this thickness is ..
Research question and hypothesis : Use the library, Internet, and other available resources to develop a 6–8 page research proposal that includes the following:Introduction to your topic "Police Discretion" and related issues (variables)
How far away from the battleship is the submarine : A battleship is using sonar (reflected underwater sound signals) to detect the presence of nearby submarines. How far away from the battleship is the submarine

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the max voltage that can be measured by voltmeter

A galvanometer has 25 divisions in full scale. Its sensitivity (k) is .2mA/div and resistance (Rg) is 50 ohms. Construct voltmeter using the galvanometer and a 2950 ohms resistor, how will you use the resistor (series or parallel to galvanometer)

  What is the rotor pole shift in electrical degrees

a) If the excitation voltage E0 is equal to the terminla voltage ( 4kV ), what is the maximum real power which the motor can deliver without losing synchronism  b) What is the rotor pole shift in electrical degrees, corresponding to the nominal loa..

  Find the snr at the output and noise figure

an amplifier with a 1 MHz bandwidth and a 20 mV input signal. The input noise = 1 mV, output signal = 6.0 mV, and output noise = 1 mV. Find: (a) SNR at the input (b) SNR at the output (c) Noise figure

  Calculate the starting current offering max points

A 440-V, 60Hz, 4-pole, delta connected three phase induction motor has the following parameters in ohms/phase. R1= .3, X1= .9, R2=.6, X2=.9 Rc=150, Xm=60 If the rotational losses are 6% of the developed power A.) determine the efficiency when i..

  How many samples of actual data are needed to resolve signal

a) Based on your decision create a sampled signal of the sum of the two sines, and plot the magnitude of the zero centered FFT with property frequency annotation. Did it work Check with the data tip tool.

  Determine the lagging power factor

A 60-Hz, single-phase transmission line has a length of 80 miles. Its shunt conductance (G) is 3.4×10?11 S/mile, resistance (R) is 0.1 ?/mile, capacitance (C) is 16 pF/mile, and inductance (L) is 0.56 mH/mile 220 kV, 220 MVA with power factor

  Determine what is the distance measured by an altimeter

An altimeter can measure 0-100m; using a signal conditioner, this high position is distributed over a voltage range of 0-5V. If an ADC covering the same voltage range outputs 1000 0000, what is the distance measured

  Find value of capacitance needed to bring current in phase

single phase motor draws 20A from a 200V, 50Hz supply with a lagging power factor of 0.8. Calculate the value of the capacitance needed to bring the current in phase with the voltage.

  Derive minimal boolean expressions for flip-flop inputs

Design a 2-bit counter that, when f = 1, counts in the repeating sequence: 0, 2, 3, and when f = 0, counts in the reverse direction. Use T flip-flops. (a) Construct a state diagram or state table. (b) Specify a state assignment.

  Explain how to recover the increased design cost

a cost to produce, P, of $4.00. If we were able to reduce this to $3.55 through greater attention in the design, and if the cost to improve the design (in NRE) is $35,000, how many units must we sell to recover the increased design cost

  Find the thevenin and norton circuits for the sensor

an unknown sensor is investigated by connecting resistors across the output and measuring the current through them. When a resistance of 30 is connected the current through it is 0.5A. When the resistance is replaced by 20

  What current flows through the resistor if resistance given

The bottom of the conduction band at one end of a silicon resistor is at the same energy level as the top of the valence band at the other end. What current flows through the resistor if the resistance is 1.12 kOhms

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd