Determine the maximum shear stress in the shaft

Assignment Help Civil Engineering
Reference no: EM13317780

The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hpis removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G ¼ 12 106 psi for steel, and assume that friction at bearing D is negligible.

Reference no: EM13317780

Questions Cloud

Calculate the total active earth force per foot of wall : Calculate the total active earth force per foot of wall and its point of application from the base of the wall. Use Rankine theory. Calculate the total active earth force per foot of wall if the angle of wall friction between backfill and wall is 2..
What is the standard deviation of total weekly waiting time : Suppose your wait time for a shuttle bus in the morning is normally distributed with µ=8 minutes and t1=5 minutes. Due to increased congestion in the afternoon, your wait time for a shuttle bus in the afternoon is normally distributed
Write a breadth-?rst search algorithm : Write an algorithm to classify the edges of a directed graph G into the four categories: tree edge, back edge, forward edge and cross edge (de?ned in De?nition 7.14, pages 342-343).
What is the the net capacitance : if 5 capacitors each of 5 micro F are connected in series with 4 capacitors each of 4 uF capacitances in parallel. what is the the net capacitance
Determine the maximum shear stress in the shaft : The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hpis removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A.
Calculate rental fee for different types of borrowable media : Assume that there is an abstract class called Vehicle, which has two concrete subclasses, Car and Truck. There is also an interface Loadable, which only Truck implements - calculate a rental fee for different types of borrowable media (e.g. books,..
Find the angle of rotation of the free end of the shaft : The solid compound shaft, made of three di¤erent materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft.
Determine the moment at point e in the compound beam : Point F is located just to the left of the 18kN and 25 kN*m couple moment. A) Determine the internal normal force at point E in the compound beam. B) Determine the shear force at point E in the compound beam.
What is the minimum oscillation frequency for this circuit : A 2.2mH inductor is connected in parallel with a variable capacitor. What is the minimum oscillation frequency for this circuit

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design cylindrical composite column consisting of steel rods

design a cylindrical composite column consisting of some steel rods, and also wrapped in nano-fiber material. The column must support a compressive axial force of 500 kips. The columns length is 5 ft.

  What will the volume of the sample be for the water content

a saturated 100 cm^3 clay sample has a natural water content of 30 percent. it is found that the shrinkage limit occurs when the water content is 19 percent. if the specific gravity of soil solids is 2.70

  Calculate the ammonia concentration in mg per l

NH4+ = N+ + NH3 pK =9.24 If the pH is 8.5 and the ammonium(NH4+) concentration in 20mg/L, calculate the ammonia(NH3) concentration in mg/L.

  Find the probability that more than 8 fail before 10 months

Suppose that under severe operation conditions, the lifetime, in months, of a transisitor is exponentially distributed with parameter d = 0.2. a. Find the probability that such a transistor lasts longer than 8 months.

  Determine the minimum footing length l of the columns

Assume a value of B, compute the allowable bearing capacity, then solve for B. Show at least 1 iteration with whatever assumed width irrespective of whether or not you get the desired Factor of safety.

  What percent of the particles does the settling tank capture

The setting velocity of a particle is 0.002 m/s and the overflow rate of a settling tank is 0.008 m/s. (a) what percent of the particles does the settling tank capture. If the particles are flocculated so that thie rsettling rate is 0.05 m/s

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 0.4-m diameter is 500 m long, the second pipe 600 m long, size 0.3 m, and the last pipe is 500 m long of diameter 0.2 m. If the elevation difference between two reservoirs is 30 m, calculate equivalent pipe size and flow in the p..

  What is the vapor pressure of carbon dioxide in the bottle

What is the vapor pressure of carbon dioxide in the bottle before it is opened (i.e., when it is at equilibrium) assuming no other ions are present besides those related to CO2 and water

  What is the spring constant

suppose you apply a force of 14.4 N to a spring and it stretches 2.4 cm. what is the spring constant?

  Explain how to estimate the long-term safety factors

A 2.0m-wide strip at a depth of 1 m in a stiff clay carries a wall load of 425 kN/m. The saturated unit weight of the caly is 20kN/m^3. TRiaixal tests give the following results: c'=10 kPa, phi'=28 degree, cu=105kPa, and phi_u = 0.

  Design a three story office building

Design a three story office building

  How far does each skater travel

If they pull themslevles along the the rope until they meet how far does each skater travel? B)If only the 45 kg skater pulls along the rope until she meets her friend( who just holds onto the rope) how far does each skater travel?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd